Results 1 to 8 of 8
  1. #1
    TheEngineer's Avatar
    Join Date
    Aug 2007
    Location
    Tampa, FL
    Posts
    934
    +1
    131

    Fuel Pump Assembly

    I was reinstalling my fuel pump today and the floating sensor got snagged and popped loose. Does anyone know how or wear this float arm clips on? Is it possible to reattach. Right now it's just loose inside the pump.

    Click image for larger version. 

Name:	photo 1.jpg 
Views:	108 
Size:	76.8 KB 
ID:	307637Click image for larger version. 

Name:	photo 2.jpg 
Views:	104 
Size:	40.2 KB 
ID:	307638


  2. #2
    Moderator beerdart's Avatar
    Join Date
    Aug 2006
    Location
    CT
    Posts
    25,930
    +1
    1,407
    It snaps into the plastic channel at the wiper.

  3. #3
    TheEngineer's Avatar
    Join Date
    Aug 2007
    Location
    Tampa, FL
    Posts
    934
    +1
    131
    Quote Originally Posted by beerdart View Post
    It snaps into the plastic channel at the wiper.
    Still can't figure it out. Could you elaborate just a bit? Do I need to separate the pieces the actual fuel pump canister to do this?

  4. #4
    TheEngineer's Avatar
    Join Date
    Aug 2007
    Location
    Tampa, FL
    Posts
    934
    +1
    131
    It looks like I might have broken a piece of the white plastic that snaps. So I'm screwed. Anyone know if the ski will still run if the fuel level sensor is disconnected?

  5. #5
    dnielsen's Avatar
    Join Date
    May 2008
    Location
    Shreveport, Louisiana
    Posts
    2,018
    +1
    94
    Devcon Plastic Epoxy (GEL), purchase at Lowes or Home Depot near or in the paint department. Comes in the twin syringe applicator that you squeeze out then mix together to activate. Drys hard as fuck and sticks to anything and works like hard plastic when set. Hardens in about 15 minutes although the package says either 3 or 5 minutes.

    Important to get the Epoxy Gel rather that the Epoxy. The Epoxy runs like syrup and the shit runs everywhere but the Gel works like peanut butter and you can wet the tips of your fingers to mold in for about a minute before it starts to set.

  6. #6
    Rt-HemiBoY's Avatar
    Join Date
    Mar 2010
    Location
    HiAleAH-MiAMi--FL
    Posts
    1,315
    +1
    24
    Yes it will still works but if I were you just try to fix it with the hard epoxy they explain in earlier thread..If not just leave it unpluggged
    Quote Originally Posted by TheEngineer View Post
    It looks like I might have broken a piece of the white plastic that snaps. So I'm screwed. Anyone know if the ski will still run if the fuel level sensor is disconnected?

  7. #7
    www.eastcoastpwc.net Scott's Avatar
    Join Date
    Jul 2007
    Location
    NJ
    Posts
    7,992
    +1
    455
    Quote Originally Posted by dnielsen View Post
    Devcon Plastic Epoxy (GEL), purchase at Lowes or Home Depot near or in the paint department. Comes in the twin syringe applicator that you squeeze out then mix together to activate. Drys hard as fuck and sticks to anything and works like hard plastic when set. Hardens in about 15 minutes although the package says either 3 or 5 minutes.

    Important to get the Epoxy Gel rather that the Epoxy. The Epoxy runs like syrup and the shit runs everywhere but the Gel works like peanut butter and you can wet the tips of your fingers to mold in for about a minute before it starts to set.
    Even tho the epoxy will be submerged in gasoline? I don't think the epoxy will last too long in this environment

  8. +1 by:


  9. #8
    westy's Avatar
    Join Date
    May 2007
    Location
    Australia (Bundaberg)
    Posts
    1,132
    +1
    45
    rather expensive but you can buy the parts separate to fix it you don't have to buy the whole pump assembly 43A 275500780 SENSOR LEVER 1 85.99

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. WTB Anyone have a trashed/scrap FICHT fuel pump assembly laying around?
    By bgaidan in forum Polaris Classifieds
    Replies: 4
    Last Post: 07-02-2015, 10:33 AM
  2. WTB WTB fuel pump assembly for 951 carb Broke the t nipple on mine.
    By ruinplay in forum Sea Doo Classifieds
    Replies: 4
    Last Post: 05-23-2011, 11:11 AM
  3. FS: Sea Doo RXP/RXT Fuel Pump Assembly
    By neversatisfiedmotorsports in forum Sea Doo Classifieds
    Replies: 1
    Last Post: 09-16-2009, 04:58 PM
  4. WTB: RXT fuel pump assembly
    By neversatisfiedmotorsports in forum Sea Doo Classifieds
    Replies: 2
    Last Post: 08-08-2009, 09:23 AM
  5. FS:RXP Fuel Pump assembly
    By Seadooracer9 in forum Sea Doo Classifieds
    Replies: 0
    Last Post: 06-22-2009, 09:40 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •