Results 1 to 6 of 6
  1. #1

    Drive shaft STXR

    Looking for a good condition drive shaft for an stxr. Please ler me know what you have.


  2. #2
    Fat Man, Little Boat Region8Ultra250X's Avatar
    Join Date
    Jun 2007
    might wanna consider doing the bearing and the oil seals as well in the thru hull while your in there.

  3. +1 by:

  4. #3
    TexasZ's Avatar
    Join Date
    May 2012
    Near San Antonio, Texas
    Quite a few with the same driveshaft....

    This Kawasaki 39159-3732 SHAFT-DRIVE is used on these models and components:

    1999 JT900-B1 900 STX DRIVE SHAFT
    2000 JT1100-C1 1100 STX D.I. DRIVE SHAFT
    2000 JT900-B2 900 STX DRIVE SHAFT
    2001 JT1100-F1 1100 STX D.I. DRIVE SHAFT
    2001 JT900-B3 900 STS DRIVE SHAFT
    2001 JT900-C1 900 STX DRIVE SHAFT
    2002 JT1100-F2 1100 STX D.I. DRIVE SHAFT
    2002 JT1200-A1 1200 STX-R DRIVE SHAFT
    2002 JT900-B4 900 STS DRIVE SHAFT
    2002 JT900-C2 900 STX DRIVE SHAFT
    2003 JT1100-G1 1100 STX D.I. DRIVE SHAFT
    2003 JT1200-A2 1200 STX-R DRIVE SHAFT
    2003 JT900-D1 900 STX DRIVE SHAFT
    2004 JT1200-C1 1200 STX-R DRIVE SHAFT
    2004 JT900-E1 900 STX DRIVE SHAFT
    2005 JT1200-C2 1200 STX-R DRIVE SHAFT
    2005 JT900-E2 900 STX DRIVE SHAFT
    2006 JT900E6F 900 STX DRIVE SHAFT

  5. #4
    Thru hull coupler and bearings are brandnew drive shaft is questionable. Only warn were the bearing rides not warn were the seals are at all. I put it back together to see if it leaks but if I purchase a used one I will only buy in like new condition.

    Thanks forbyour help guys

  6. #5
    crashhard's Avatar
    Join Date
    Jul 2007
    Philly PA, Wildwood NJ, Indialantic FL
    I have it, will get a picture tonight. Thanks

  7. #6
    Guys not needed. After putting it all back together it still leaked. Found the aluminum thru hull separated from the hull. Cleaned and glued with 5200

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. carbon seal, drive shaft seal??
    By CarFanatic in forum 4-Tec Performance
    Replies: 5
    Last Post: 08-06-2006, 02:13 AM
  2. GP1200 drive shaft damper
    By hitman in forum Yamaha PWC Performance (2-stroke)
    Replies: 6
    Last Post: 08-01-2006, 10:23 PM
  3. Drive Shaft Plug Replacement
    By 1FastTrespiper in forum Sea Doo Open Discussion
    Replies: 6
    Last Post: 07-17-2006, 10:47 PM
  4. how to remove rear drive shaft coupler
    By chuck in forum Yamaha PWC Performance (2-stroke)
    Replies: 2
    Last Post: 02-20-2006, 08:37 AM
  5. aftermarket drive shaft question...
    By dewsy in forum 4-Tec Performance
    Replies: 4
    Last Post: 01-26-2006, 07:47 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts