Results 1 to 8 of 8
  1. #1

    Join Date
    Aug 2007
    Location
    Port Saint Lucie Florida
    Posts
    77
    +1
    1

    Question little help --- proper name carb linkage parts

    I need a little help what is the proper name carb linkage parts , where the rod connects all three carb to the throttle plate, I am calling this a "ball joint" but there has to be a proper name for this part?????

    I have the triple carb rod and the throttle plates but I need three of those ball joints there the part witha ball on one end that clips into the linkage rod and they have threads and nut an the other end. Any hints on teh proper name so I can try to find some would be great!!


  2. #2

    Join Date
    Sep 2013
    Location
    Austin, TX
    Posts
    83
    +1
    4
    Name:  R348998-01.jpg
Views: 49
Size:  7.0 KBTechnically its a ball and socket joint. Ball is metal and the socket is plastic on my mikuni carbs. Why not look up the actual part number from a parts diagram though.

  3. #3
    Happily Self-Employed WFO's Avatar
    Join Date
    Nov 2005
    Location
    Houston, Texas
    Posts
    12,800
    +1
    449
    We usually just call it a carb linkage rod

    What type of craft? I have a bunch of triple throttle linkage rods in stock

    EDIT: I see you need something besides the rod that snaps onto the ball ends

  4. #4

    Join Date
    Aug 2007
    Location
    Port Saint Lucie Florida
    Posts
    77
    +1
    1
    I actual tried but none of the carb diagrams I looked at had the actual linkage it was just show the single carb disassemble unless I looked in wrong place. That picture is different type then I have but that ball part is what I need the rod or socket I have is the stock mikuni rod .

    The ski is a project but teh engine is a non-pv xl200 form a 1998 yamaha carbs are mikuni suber BN

  5. #5

    Join Date
    Aug 2007
    Location
    Port Saint Lucie Florida
    Posts
    77
    +1
    1
    WFO,
    yep have the rod I need the ball ends that snap into the rod

  6. #6
    Happily Self-Employed WFO's Avatar
    Join Date
    Nov 2005
    Location
    Houston, Texas
    Posts
    12,800
    +1
    449
    Quote Originally Posted by yama-doo View Post
    WFO,
    yep have the rod I need the ball ends that snap into the rod
    contact these guys... they do a lot of custom carb work and may have what you need in stock

    http://www.jetworksperformance.com/?page_id=2

  7. #7

    Join Date
    Aug 2007
    Location
    Port Saint Lucie Florida
    Posts
    77
    +1
    1
    thanks

  8. #8
    Happily Self-Employed WFO's Avatar
    Join Date
    Nov 2005
    Location
    Houston, Texas
    Posts
    12,800
    +1
    449
    The part you are looking for is usually made onto the throttle shaft "arm", but aftermarket companies (Novi, Blackjack, Full Spectrum) use aftermarket throttle plates, levers and linkages. The guys I gave you the link to do the Blackjack mods. I have some 48 Blackjacks sitting here that have what you are looking for already installed

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Replies: 6
    Last Post: 04-25-2012, 08:31 AM
  2. Replies: 0
    Last Post: 04-15-2012, 01:05 PM
  3. Need a little help from all your HULKsters!
    By beachboy66 in forum 4-Tec Performance
    Replies: 2
    Last Post: 07-20-2006, 07:38 AM
  4. Little help please
    By CRAZEDRXP in forum Sea Doo Open Discussion
    Replies: 18
    Last Post: 06-01-2006, 02:38 PM
  5. Can some one Post! A little Help Please!
    By Angelse68cal in forum 4-Tec Performance
    Replies: 6
    Last Post: 08-04-2005, 07:57 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •