Results 1 to 10 of 33
-
04-25-2014, 06:40 PM #1
- Join Date
- Feb 2014
- Location
- Whitman MA
- Posts
- 16
Need help with a 2002 virage 800i
Any help would be greatly appreciated. I bought the ski knowing it needed the emm repaired. I have had the emm fixed The problem is the ski starts and immediately stalls. I installed Kawasaki inline fuel pressure regulator. New tps. I have proper voltage to injectors. Fuel pressure is around 25 psi. Compression is 150 psi on both cylinders. I can get it to run with fuel down the throttle bodies. I do not know if the injectors have been swapped out. Any thoughts or suggestions would be great. Thanks
-
04-25-2014, 07:08 PM #2
So its pretty clear you probably have spark and are not getting fuel. First place I would look is the stator output if the emm is known yo be good. Check the voltage at the injectors and see what you get. Should be around 20 volts cranking and around 45 volts running.
-
04-25-2014, 07:08 PM #3
- Join Date
- Jul 2007
- Location
- near Toronto, Canada
- Posts
- 37,364
- +1
- 1,425
Welcome
Does it stay running if you first disconnect the TPS and then start it?
If still not stay running, put a multimeter red probe on the White/Red injector power wires (black probe to engine ground).
Do not unplug an injector, find some other place to tap into the White/Red wires. Voltage should jump up to around 45 volts as soon as the engine starts and remain fairly stable.
-
04-25-2014, 07:18 PM #4
- Join Date
- Feb 2014
- Location
- Whitman MA
- Posts
- 16
Voltage is 45 at injectors when it starts.
-
04-25-2014, 07:22 PM #5
- Join Date
- Feb 2014
- Location
- Whitman MA
- Posts
- 16
Not sure if this is an issue or not but the ski cranks without the lanyard installed.
-
04-25-2014, 07:33 PM #6
That very well could be the issue. I bet you have a bad start stop module.
-
04-25-2014, 07:48 PM #7
-
04-26-2014, 01:53 PM #8
- Join Date
- Feb 2014
- Location
- Whitman MA
- Posts
- 16
I bypassed lr503 module and still cranks without lanyard and does not run without start button pressed. With module bypassed it will crank but no start. Does not wake up instrument panel until lanyard is in.
-
04-26-2014, 04:36 PM #9
-
04-27-2014, 06:45 AM #10
- Join Date
- Feb 2014
- Location
- Whitman MA
- Posts
- 16
It is running on 2 cylinders. Does not respond to throttle. I can keep it going by dumping fuel into the intake.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
NEED HELP!!!! No spark 2002 Virage TX
By 2boys2skis in forum Polaris Open DiscussionReplies: 7Last Post: 07-04-2015, 05:58 PM -
Need Help with 2002 F12X Engine Install
By toddkageals in forum Honda Open DiscussionReplies: 0Last Post: 08-08-2011, 09:34 AM -
I need some help with a 2002 RXDI
By planiack in forum Sea Doo Open DiscussionReplies: 1Last Post: 01-27-2010, 08:38 PM -
Need help with a 2001 Virage Tx
By grammylinny in forum Polaris Open DiscussionReplies: 27Last Post: 07-01-2007, 08:06 PM -
Need Help With Virage..
By Alex3012red in forum Polaris Open DiscussionReplies: 10Last Post: 01-17-2007, 07:27 AM
NEW ET 142 w/ET 300 charger water cooler;)..............BINESS!!!!!!!!8-)
2007-2018 RXP/RXPX Thread of the...