Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11
  1. #1

    Join Date
    Aug 2007
    Location
    Idaho
    Posts
    174
    +1
    29

    SVHO Question...Need help

    I am 500 miles away from my ski right now and trying to make sure I have all the required parts to finish my upgrades.

    Can someone tell me what the I.D of the hoses coming out of the intercooler that piss out hull? More importantly is the hose barb diameter on those thru-hull fittings. I am wanting to route my Fizzle intercooler "out" hose thru those 2 fittings.

    Thanks in advance!


  2. #2

    Join Date
    Aug 2007
    Location
    Idaho
    Posts
    174
    +1
    29
    73 Views and no reply....

    Can someone that owns a SVHO ski go disconnect 1 of the 2 hoses on the stock intercooler and tell me what the inside diameter of the hose is please?

    Thanks

  3. #3
    big john's Avatar
    Join Date
    Sep 2010
    Location
    Cocoa Beach, Florida, United States
    Posts
    3,395
    +1
    598
    1/2"

  4. #4
    zone5's Avatar
    Join Date
    Feb 2013
    Location
    West of Blue Mountains, Australia
    Posts
    373
    +1
    36
    Sorry, yes I did view but it's a little hard to check when the ski is in Sydney and I'm in London...

  5. #5
    Chupacobra's Avatar
    Join Date
    Jun 2012
    Location
    Orlando, FL
    Posts
    1,372
    +1
    408
    The feed is half the exit might be 3/8. Not sure

  6. #6

    Join Date
    Aug 2007
    Location
    Idaho
    Posts
    174
    +1
    29
    Quote Originally Posted by big john View Post
    1/2"
    Thanks Big John! Very much appreciated.

  7. #7
    YudLuz2's Avatar
    Join Date
    Jun 2005
    Location
    Flowood MS
    Posts
    1,647
    +1
    110
    The ends swell up really big on the end of those two hoses. The hoses will slide up on a 5/8 barb fitting very easily. I used a 1/2 barb on my last 2014 and they were very loose, clamped them down with a big hose clamp and there holding fine. It might be better to cut about a inch off the hose to get back down to the normal size of the hose, but there probably going to be too short to use without adding some length.

  8. #8

    Join Date
    Aug 2007
    Location
    Idaho
    Posts
    174
    +1
    29
    Quote Originally Posted by YudLuz2 View Post
    The ends swell up really big on the end of those two hoses. The hoses will slide up on a 5/8 barb fitting very easily. I used a 1/2 barb on my last 2014 and they were very loose, clamped them down with a big hose clamp and there holding fine. It might be better to cut about a inch off the hose to get back down to the normal size of the hose, but there probably going to be too short to use without adding some length.
    Thanks for the heads up Ben. I will be adding length with my "out" line...so I will cut an inch or 2 off of them. Likely the thru-hull pissers are 1/2" barb then?

  9. #9
    JFizzleJR's Avatar
    Join Date
    Aug 2005
    Location
    FL
    Posts
    8,628
    +1
    808
    I now have 1/2" x 1/2" x 1/2" Y fittings that will make the setup look clean. I'm not sure if you already found a fitting but let me know if I can help you out. They are brass fittings.

  10. #10
    JROD06's Avatar
    Join Date
    Mar 2014
    Location
    Mobile, AL
    Posts
    51
    +1
    3
    Jfizzlejr,
    can you send me the Y, I can't find one anywhere and ordered my fizzle kit a few weeks ago, must say I love the fit and finish of your intercooler by the way. I ended up just using the splice fitting that was replaced with a T from the cooling kit and now am only using one of the out threw hull fittings until I can get a Y.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. '02 Virage 800i fuel injection questions... need HELP!
    By ProXR 440 in forum Polaris How To & FAQs
    Replies: 4
    Last Post: 06-17-2009, 01:07 PM
  2. UMI questions, need help!
    By Pale Rider in forum Yamaha PWC Performance (2-stroke)
    Replies: 5
    Last Post: 05-10-2009, 08:45 PM
  3. speed questions????? need help please!
    By 1fastrat in forum 2-Stroke Performance
    Replies: 18
    Last Post: 08-25-2008, 11:07 AM
  4. Quick Question- need help RXT-X
    By Bigcat1 in forum 4-Tec Performance
    Replies: 3
    Last Post: 05-25-2008, 04:17 PM
  5. Riva IC questions (need help)
    By gotpurp305 in forum 4-Tec Performance
    Replies: 3
    Last Post: 04-11-2006, 10:27 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •