Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11

Thread: HKS bov help

  1. #1
    CARLRRE's Avatar
    Join Date
    May 2005
    Location
    VIRGINIA
    Posts
    146
    +1
    3

    HKS bov help

    I have a 2014 FX SVHO Cruiser nod have just finished installing the Fizzle inter cooler and bov and now I need to install the vacuum line and there is no place to hook it to the engine. HELP JJERRY, can you help? Everything is back together. Instructions. Don't say a thing on where the vacuum line goes.


  2. #2
    JFizzleJR's Avatar
    Join Date
    Aug 2005
    Location
    FL
    Posts
    8,626
    +1
    806
    There are several options. You can tap the intake manifold, use an R&D map sensor adapter, or T the line at the map sensor to name a few.

    Quote Originally Posted by CARLRRE View Post
    I have a 2014 FX SVHO Cruiser nod have just finished installing the Fizzle inter cooler and bov and now I need to install the vacuum line and there is no place to hook it to the engine. HELP JJERRY, can you help? Everything is back together. Instructions. Don't say a thing on where the vacuum line goes.

  3. #3
    shrabber's Avatar
    Join Date
    Apr 2008
    Location
    Jacksonville, FL
    Posts
    5,305
    +1
    376
    Here is some pics, Go pick you up 1/8 npt x 1/8Hb fitting and use a 11/32 drill bit. Drill hole tap with 1/8 npt/27 and done
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	IMG_2415.jpg 
Views:	126 
Size:	66.1 KB 
ID:	334598   Click image for larger version. 

Name:	IMG_2414.jpg 
Views:	158 
Size:	64.4 KB 
ID:	334599   Click image for larger version. 

Name:	image.jpg 
Views:	119 
Size:	79.7 KB 
ID:	334600   Click image for larger version. 

Name:	image.jpg 
Views:	134 
Size:	77.3 KB 
ID:	334601  

  4. #4
    CARLRRE's Avatar
    Join Date
    May 2005
    Location
    VIRGINIA
    Posts
    146
    +1
    3
    Thanks for the quick reply. Can't wait to get it in the water to see the difference in performance. Did all the up grades that Jerry recommend and wii send the ecu off later for a reflash.

  5. #5
    JFizzleJR's Avatar
    Join Date
    Aug 2005
    Location
    FL
    Posts
    8,626
    +1
    806
    Thanks Tim!

    Quote Originally Posted by shrabber View Post
    Here is some pics, Go pick you up 1/8 npt x 1/8Hb fitting and use a 11/32 drill bit. Drill hole tap with 1/8 npt/27 and done
    Quote Originally Posted by CARLRRE View Post
    Thanks for the quick reply. Can't wait to get it in the water to see the difference in performance. Did all the up grades that Jerry recommend and wii send the ecu off later for a reflash.
    The reflash will be the most important part of it all

  6. #6
    CARLRRE's Avatar
    Join Date
    May 2005
    Location
    VIRGINIA
    Posts
    146
    +1
    3
    I tried to find the link in the store for your intercooler Mr. Fizzle and it didn't seem to be listed. I was on a friends tablet earlier when I asked the question for this thread and was having a lot of trouble with my fumble fingers making it work. I will try and send off my ecu next Mo nday to R and D for the R3 reflash. So looking forward to having a very rapid FX. I hope that I can get it back in the same week. Hopefully next day air will get the job done

  7. #7
    JFizzleJR's Avatar
    Join Date
    Aug 2005
    Location
    FL
    Posts
    8,626
    +1
    806
    I'm sorry to hear that you had trouble finding it. Next time just send me a message and I'll get back to you right away.

    Here is the direct link to the Fizzle Y1000 Yamaha Intercooler Kit installation instructions: http://fizzlefactory.com/instruction...structions.pdf

    Quote Originally Posted by CARLRRE View Post
    I tried to find the link in the store for your intercooler Mr. Fizzle and it didn't seem to be listed. I was on a friends tablet earlier when I asked the question for this thread and was having a lot of trouble with my fumble fingers making it work. I will try and send off my ecu next Mo nday to R and D for the R3 reflash. So looking forward to having a very rapid FX. I hope that I can get it back in the same week. Hopefully next day air will get the job done

  8. #8
    CARLRRE's Avatar
    Join Date
    May 2005
    Location
    VIRGINIA
    Posts
    146
    +1
    3
    JFizzle, I just installed your y1000 on my ski. Just finished today. I knew the instructions were on the Greenhulks store site when I purchased mine from Greenhulk. I was looking for it again today when I couldn't seem to make it come up on the stores website. That is when I asked for your direct help and I appreciate your quick reply on the bov thing. Going to try and get it wet tomorrow before the hurricane messes up the lake where I ride most of the time.

    I just went to the store and looked in the yamaha performance parts section and your intercooler isn't listed any more. Not sure what is going on.

  9. #9
    JFizzleJR's Avatar
    Join Date
    Aug 2005
    Location
    FL
    Posts
    8,626
    +1
    806
    Carl,

    The link is gone from the 4-tecperformance store because they are sold out and on backorder.

    Quote Originally Posted by CARLRRE View Post
    JFizzle, I just installed your y1000 on my ski. Just finished today. I knew the instructions were on the Greenhulks store site when I purchased mine from Greenhulk. I was looking for it again today when I couldn't seem to make it come up on the stores website. That is when I asked for your direct help and I appreciate your quick reply on the bov thing. Going to try and get it wet tomorrow before the hurricane messes up the lake where I ride most of the time.

    I just went to the store and looked in the yamaha performance parts section and your intercooler isn't listed any more. Not sure what is going on.

  10. #10
    Lake Lion
    Join Date
    Jul 2007
    Location
    Dirty Jerzey
    Posts
    771
    +1
    117
    Are the new fizz coolers going to have the TiAl flange? When are more I/C's expected?

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. HKS BOV
    By R3_killa in forum Yamaha PWC Performance (4-stroke)
    Replies: 248
    Last Post: 05-14-2010, 02:46 PM
  2. Can corrosion cause an HK Bov to not operate?
    By tsho in forum Yamaha PWC Performance (4-stroke)
    Replies: 24
    Last Post: 10-30-2009, 02:39 PM
  3. New Riva HKS BOV kit shipping next week
    By Green Hulk in forum Yamaha PWC Performance (4-stroke)
    Replies: 14
    Last Post: 07-29-2009, 01:10 PM
  4. Known HKS BOV issues
    By Under_Pressure in forum Yamaha PWC Performance (4-stroke)
    Replies: 29
    Last Post: 07-12-2009, 08:19 AM
  5. HKS BOV query ??
    By wakeboardmuppet in forum Yamaha PWC Performance (4-stroke)
    Replies: 7
    Last Post: 04-09-2009, 06:05 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •