Results 1 to 8 of 8
  1. #1

    Tial 50mm BOV Install Question

    Guys,

    I have a R&D Tial 50mm BOV kit that I am planning to install on a 2014 FX-SVHO. Does anyone have a copy of the R&D supplied instructions they can email or PM me? Any help would be much appreciated!

    Thanks,
    Chris


  2. #2
    LugNutLS1's Avatar
    Join Date
    Jun 2014
    Location
    St. Louis Mo
    Posts
    594
    +1
    53
    I will be installing one on my fx svho this weekend. I figured it would be basically just swapping out the SC discharge tubing and run the reference line? I already have the intake tapped with a 1/8"nptx1/4 barb installed. Does the BOV come in pieces that must be assembled too?

  3. #3
    superair's Avatar
    Join Date
    Aug 2008
    Location
    Smith Lake, Alabama
    Posts
    424
    +1
    20
    You only have to install the trigger line fitting to the top of the bov. Then install the o ring to the flange and clamp them together.

  4. #4
    My main question is do you have to tap the manifold? If so, can someone provide directions on where?

    Everything else seems straight forward.

    Quote Originally Posted by LugNutLS1 View Post
    I will be installing one on my fx svho this weekend. I figured it would be basically just swapping out the SC discharge tubing and run the reference line? I already have the intake tapped with a 1/8"nptx1/4 barb installed. Does the BOV come in pieces that must be assembled too?

  5. #5
    superair's Avatar
    Join Date
    Aug 2008
    Location
    Smith Lake, Alabama
    Posts
    424
    +1
    20
    Yes you need a separate line for this. Most tap the front zip tie boss on the intake manifold. You will need an 11/64" drill bit and a 1/8" pipe thread tap.

  6. +1 by:


  7. #6
    LugNutLS1's Avatar
    Join Date
    Jun 2014
    Location
    St. Louis Mo
    Posts
    594
    +1
    53
    You must do this with the intake off. I did the ribbon delete at same time since it was off. See here for reference on tapping of intake http://www.greenhulk.net/forums/show...ntake+manifold

  8. #7
    LugNutLS1's Avatar
    Join Date
    Jun 2014
    Location
    St. Louis Mo
    Posts
    594
    +1
    53
    I have seem many threads where people tried to t into the map sensor line. Most often this caused problems with the MAP signal. Just tap into the manifold and do it right the first time to avoid problems

  9. #8
    Thanks for the responses. I'll plan to tap the manifold as I'm pulling it for the ribbon delete anyway.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Which spring to use with Tial 50mm BOV?
    By Jmfmk3 in forum Yamaha PWC Performance (4-stroke)
    Replies: 17
    Last Post: 09-08-2014, 10:19 AM
  2. Tial 50mm R&D BOV installed , riva FF sounds quite.
    By pasek74 in forum Yamaha PWC Performance (4-stroke)
    Replies: 3
    Last Post: 08-14-2014, 08:48 AM
  3. SOLD Tial 50mm BOV mounted
    By jetpilot785 in forum Yamaha Classifieds
    Replies: 0
    Last Post: 07-25-2012, 04:31 PM
  4. FS TiAl 50mm BOV FS
    By Slow 91 in forum Sea Doo Classifieds
    Replies: 1
    Last Post: 04-04-2011, 07:00 AM
  5. bov kit install question
    By TroyRXP15 in forum 4-Tec Performance
    Replies: 3
    Last Post: 08-15-2005, 09:16 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •