Page 1 of 2 1 2 LastLast
Results 1 to 10 of 14
  1. #1

    Join Date
    Jul 2014
    Location
    Iowa
    Posts
    22
    +1
    5

    R&D mods on my 310x

    Took out my 310x today with the new mods. R&D reflash, BOV, Intake Grate, Ride Plate. I have a 14/19 Impeller and 1* wedge to put on but my tool didn't show up in time so I just tried it without it. 85* water, 93* air temp, very light chop and 1/4 tank of fuel. Hit 73.5 mph a few times with many 73.2 readings. Around 7800rpm's. All and all I was happy with the results I think? from what I have read it seems to b about right for the mods I have. Hope to get the Impeller on this week and try it out. Ill keep everyone updated.

    What does anyone think the Impeller and wedge will do? Will it make much difference?


  2. #2
    Take the time to smile sirbreaksalot's Avatar
    Join Date
    Jun 2007
    Location
    Brisvegas
    Posts
    4,157
    +1
    598
    seems slow to me and the RPM's are low, basically only 150 ish over stock ..if you are still on the stock prop !!

  3. #3

    Join Date
    Oct 2013
    Location
    Lake of the ozarks 30.5mm
    Posts
    6
    +1
    1
    Would have probably ran faster if you did not have that cheap missouri gas in it.

  4. #4
    Take the time to smile sirbreaksalot's Avatar
    Join Date
    Jun 2007
    Location
    Brisvegas
    Posts
    4,157
    +1
    598
    if by cheap you mean non premium ....then you are playing with death ,

  5. #5

    Join Date
    Jul 2014
    Location
    Iowa
    Posts
    22
    +1
    5
    We rode with him Thursday. He is just giving me crap. We were using 93

  6. #6

    Join Date
    Oct 2013
    Location
    Lake of the ozarks 30.5mm
    Posts
    6
    +1
    1
    Brian, you missed a good shootout. A 244mph 50 foot twin turbine mti cat and and a 179mph outerlimits cat that flipped end over end.

  7. #7

    Join Date
    Jul 2014
    Location
    Iowa
    Posts
    22
    +1
    5
    Kevin, was that the big red outerlimits? did you see that white boat run we saw at captian rons?

  8. #8
    Spooling's Avatar
    Join Date
    Sep 2011
    Location
    West Coast of Florida
    Posts
    1,283
    +1
    177
    Your Highest RPM reading must be read while running near your Top Speed - as - "stored" RPM displayed on your MFD is always different and stores a numerical value that is < the "live" RPM reading while you are running WFO.

    Explanation why - Reference:

    http://www.greenhulk.net/forums/show...=1#post2277534

    Your speed should come-up with the installation of the wedge and you can also try to get more air in your hull. Pick and choose what will work best for you here:

    http://www.greenhulk.net/forums/show...light=air+mods

    Good Job and Good Luck !!!



  9. #9

    Join Date
    Oct 2013
    Location
    Lake of the ozarks 30.5mm
    Posts
    6
    +1
    1
    Brian, google offshore lake of the ozarks. They have pictures of the wreck and a picture of the white boat. I did not get to see the white boat run, did watch him put it on the trailer about 2 hours ago.

  10. #10
    You should also remove the honeycomb screen in the exhaust system. R&D sell a plate to replace it in the exhaust.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Looking for someone to assist with install of mods on my 1200 XLL
    By RipNSki in forum Yamaha Open Discussion
    Replies: 5
    Last Post: 01-11-2011, 08:01 PM
  2. My first mod on my VX, gas cap is on!
    By SlowStang305 in forum Yamaha Open Discussion
    Replies: 1
    Last Post: 04-03-2009, 05:52 PM
  3. 66.2mph with minor mods on my 15f
    By wave15stx in forum Kawasaki PWC Performance (4-stroke)
    Replies: 64
    Last Post: 11-17-2007, 07:05 PM
  4. first mod on my new RXT????
    By havoc in forum 4-Tec Performance
    Replies: 6
    Last Post: 07-12-2007, 01:41 AM
  5. Mods on my 06 RXP
    By Pirates81 in forum 4-Tec Performance
    Replies: 1
    Last Post: 03-30-2007, 07:41 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •