Page 1 of 2 1 2 LastLast
Results 1 to 10 of 15
  1. #1

    Join Date
    Feb 2014
    Location
    Sydney Australia
    Posts
    125
    +1
    12

    Bilge pump outlet position

    Looking at putting a bilge pump in my seadoo rxp does anyone have a picture of the outlet or can you connect it to the ehaust water outlet. Do you need a check valve on the outlet hose also.

    thanks in advance for your help.


  2. #2
    Q in Arizona's Avatar
    Join Date
    May 2013
    Location
    Phoenix, Az
    Posts
    30,415
    +1
    7,298
    Here's the install I did on my GTR...and no...you really don't need a check valve if the outlet is in a proper location. There's plenty more bilge pump install photo's in that thread to look at too.

  3. #3
    canuck's Avatar
    Join Date
    May 2006
    Location
    The wet left coast.
    Posts
    1,088
    +1
    108
    Next to the tow hook on a previous RXP. I did not install a check valve since the outlet is well above the waterline.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	IMG_0592.jpg 
Views:	145 
Size:	51.4 KB 
ID:	344822  
    Last edited by canuck; 10-23-2014 at 12:53 PM.

  4. #4
    canuck's Avatar
    Join Date
    May 2006
    Location
    The wet left coast.
    Posts
    1,088
    +1
    108
    Double post.

  5. #5
    Got Boost? psycho rxp's Avatar
    Join Date
    Jul 2005
    Location
    Port St. Lucie, FL
    Posts
    5,445
    +1
    182
    Click image for larger version. 

Name:	IMG_0011.jpg 
Views:	81 
Size:	125.8 KB 
ID:	344873Click image for larger version. 

Name:	IMG_1280.jpg 
Views:	89 
Size:	102.6 KB 
ID:	344872



    Behind the Reg. #'s

  6. #6
    Tucka's Avatar
    Join Date
    Jun 2012
    Location
    mount warrigal NSW Australia
    Posts
    106
    +1
    14
    Jafo with my rxpx I put the outlet at the back where you see the BRP round sticker below the seat . I peeled off the sticker drilled a pilot hole in the centre then put electrical tape so that when I use the hole saw you don't chip the paint . Then I put in the black Blowsion outlet I got from AJSP Queensland. Hope that helped

  7. #7

    Join Date
    Feb 2014
    Location
    Sydney Australia
    Posts
    125
    +1
    12
    Thanks for your help guys going to tackle the install now.
    Cheers

  8. #8
    Q in Arizona's Avatar
    Join Date
    May 2013
    Location
    Phoenix, Az
    Posts
    30,415
    +1
    7,298
    Quote Originally Posted by Jafo View Post
    Thanks for your help guys going to tackle the install now.
    Cheers
    Good luck. Post pictures when you're done please.

  9. #9

    Join Date
    Dec 2012
    Location
    MA
    Posts
    146
    +1
    12
    This is the set up I put on my 14 tx. the outlets sit about 6-7" above the waterline when the ski is just sitting in the water.
    I made a bracket for the switches and used the rear hook bolts to secure it.




    Click image for larger version. 

Name:	IMG_1861.jpg 
Views:	92 
Size:	60.1 KB 
ID:	345017Click image for larger version. 

Name:	IMG_1862.jpg 
Views:	94 
Size:	91.8 KB 
ID:	345018Click image for larger version. 

Name:	IMG_1863.jpg 
Views:	99 
Size:	116.4 KB 
ID:	345019Click image for larger version. 

Name:	IMG_1864.jpg 
Views:	95 
Size:	77.6 KB 
ID:	345020
    Last edited by JohnW; 10-27-2014 at 04:22 AM.

  10. #10
    Tucka's Avatar
    Join Date
    Jun 2012
    Location
    mount warrigal NSW Australia
    Posts
    106
    +1
    14
    Click image for larger version. 

Name:	20141026_172253.jpg 
Views:	65 
Size:	107.2 KB 
ID:	345093Click image for larger version. 

Name:	20141027_191604.jpg 
Views:	82 
Size:	59.5 KB 
ID:	345094Click image for larger version. 

Name:	20141027_191636.jpg 
Views:	79 
Size:	81.9 KB 
ID:	345095Click image for larger version. 

Name:	20141026_172331.jpg 
Views:	63 
Size:	32.1 KB 
ID:	345096Click image for larger version. 

Name:	20141027_191342.jpg 
Views:	68 
Size:	84.3 KB 
ID:	345097

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Need bilge pump outlet fitting location advice
    By atldude in forum Sea Doo Open Discussion
    Replies: 22
    Last Post: 09-01-2016, 06:15 PM
  2. bilge pump outlet location
    By SDM24 in forum Yamaha Old School Skis
    Replies: 3
    Last Post: 06-30-2015, 10:24 AM
  3. RXP Bilge Pump install
    By Vern in forum 4-Tec Performance
    Replies: 14
    Last Post: 08-27-2014, 10:04 AM
  4. RXP bilge pump install... Transom outlet ???'s
    By jtskier11 in forum 4-Tec Performance
    Replies: 25
    Last Post: 07-10-2009, 12:33 PM
  5. For those of you looking to put a bilge pump in your Ski....
    By Jeff C in forum Sea Doo Open Discussion
    Replies: 1
    Last Post: 06-22-2005, 12:22 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •