Results 1 to 9 of 9
  1. #1

    Bildge pump help!!

    Can some post a pic of their bilge pump outlet or tell me where it's suppose to go, so I don't drill a hole in an structurally important place.


  2. #2
    GasResearch-VT.SE's Avatar
    Join Date
    Nov 2012
    Location
    Melbourne, Australia
    Posts
    1,172
    +1
    207
    Into the pump box at top or sides is fine

  3. #3
    Just worried about water flowing back down the tube, into the hull.

  4. #4
    GasResearch-VT.SE's Avatar
    Join Date
    Nov 2012
    Location
    Melbourne, Australia
    Posts
    1,172
    +1
    207
    Then make sure you have a hi point in the line

  5. #5
    I have a 2011 GTX and I installed the pump water exit over the BRP sign in the back on the hull. Don't do it lower because it will maybe pickup water to the inside of the hull. When you do it, do it with an automatic floating switch. In the case of an emergency you will rapidly known that you have problems because you will clearly see the water coming out. Install both ( pump and floating switch) in both sides of the carrier ( if you have and emergency you will be running to coast and the water will accumulate in the back on the jetski by gravity , don't install it in the lower part of the hull ( in the front of the engine - you will pickup a lot of water until it reaches the front of the engine to activate the pump.

  6. #6

  7. +1 by:


  8. #7
    suicidebonger's Avatar
    Join Date
    Feb 2009
    Location
    Michigan
    Posts
    326
    +1
    73
    On the left side towards the rear of the hull there is an indentation, all ready for a drill bit for the bilge pump. At the rear of the ski there is the plastic "T" that the plastics/body mount on. This is where you can zip tie your hose, with air hole up of course. I never got water in my hull, and installation was according to the directions.

  9. #8
    suicidebonger's Avatar
    Join Date
    Feb 2009
    Location
    Michigan
    Posts
    326
    +1
    73
    See the white outlet by sponson? Inside the hull at that point there ia marked location. I tightened mine and pinched the seal, need to fix it in the spring, don't do the same. Click image for larger version. 

Name:	DSCF7122.jpg 
Views:	113 
Size:	152.3 KB 
ID:	348560

  10. #9
    Quote Originally Posted by suicidebonger View Post
    See the white outlet by sponson? Inside the hull at that point there ia marked location. I tightened mine and pinched the seal, need to fix it in the spring, don't do the same. Click image for larger version. 

Name:	DSCF7122.jpg 
Views:	113 
Size:	152.3 KB 
ID:	348560
    Thanks!!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Ultimate Bildge Pump Install
    By tomgtv in forum Kawasaki PWC Performance (2-stroke)
    Replies: 2
    Last Post: 03-31-2008, 08:30 PM
  2. Bilge Pump help
    By jetskier90 in forum Yamaha Open Discussion
    Replies: 8
    Last Post: 03-18-2008, 06:33 PM
  3. pump help need now
    By bajaeater in forum Yamaha PWC Performance (2-stroke)
    Replies: 31
    Last Post: 01-26-2008, 12:00 PM
  4. Need to replace the pump. HELP
    By Alex Speedster 200 in forum Sea Doo Sport Boats
    Replies: 0
    Last Post: 09-12-2007, 02:50 PM
  5. More ext pump help please
    By novanuttz in forum Polaris Open Discussion
    Replies: 3
    Last Post: 06-03-2007, 02:32 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •