Results 1 to 4 of 4
  1. #1

    Msx150 rebuild finally !!!!!

    So ordered the parts I needed to rebuild my engine in my ski as I had purchased this as a non runner fairly cheap during the end of last season. Got the block out and stripped down to find it had spun the bearings on the conrods and the nikasil plating had started flaking off the cylinder walls.

    so after much waiting , reading forum after forum I gathered all the info I needed to no.

    so about 3 months ago I sent the block away and had to steel liners fitted to replace the old nikasil plating, bear in mind I've not long had the block back as the company I used were very unprofessional and a royal pain in the arse. But waited it out and £470 later I got the block back.

    so now I was in need of parts so I jumped online and searched up weber power where I've been able to get everything I need bit of the expensive side as I have to import all the parts but what a fast delivery time , so was very impressed.

    So been quite busy past couple of days cleaning up all the parts and measuring bearings ready for re assemble and this is where I'm at so far .Click image for larger version. 

Name:	image.jpg 
Views:	60 
Size:	56.7 KB 
ID:	348566Click image for larger version. 

Name:	image.jpg 
Views:	61 
Size:	96.2 KB 
ID:	348565
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	image.jpg 
Views:	57 
Size:	83.9 KB 
ID:	348564   Click image for larger version. 

Name:	image.jpg 
Views:	54 
Size:	88.3 KB 
ID:	348567   Click image for larger version. 

Name:	image.jpg 
Views:	46 
Size:	93.0 KB 
ID:	348568  


  2. #2
    ripcuda's Avatar
    Join Date
    May 2010
    Location
    Newman Lake, WA
    Posts
    2,389
    +1
    166
    Nice! I know this path well.

    Did you get the Wiseco pistons from WeberPower? I did and I too have my block sleeved. The Wiseco pistons dropped the compression from stock 9.0:1 to 8.5:1... which on a turbo engine should help fend off pre-detonation.

    Cheers!

  3. #3
    hill160881's Avatar
    Join Date
    Jun 2014
    Location
    The delta Ca
    Posts
    2,043
    +1
    246
    Looking good. Dont quit and it will be a good ski when you are done.

  4. #4
    ripcuda's Avatar
    Join Date
    May 2010
    Location
    Newman Lake, WA
    Posts
    2,389
    +1
    166
    Any progress on this Weber rebuild?

    Cheers!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. MSX150 - to rebuild or part out
    By dchrisrea in forum MSX/Matrix
    Replies: 16
    Last Post: 07-19-2011, 01:00 AM
  2. finally finished my rebuild
    By stevorxp007 in forum 4-Tec Performance
    Replies: 3
    Last Post: 11-24-2010, 01:13 PM
  3. finally finished my rebuild
    By stevorxp007 in forum 4-Tec Performance
    Replies: 1
    Last Post: 11-17-2010, 10:51 PM
  4. Polaris MSX150 idling high after rebuild?
    By Aus in forum MSX/Matrix
    Replies: 2
    Last Post: 09-25-2008, 06:56 PM
  5. Finally in the water
    By Sunfunzoom in forum 4-Tec Performance
    Replies: 3
    Last Post: 05-09-2005, 08:07 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •