Page 1 of 2 1 2 LastLast
Results 1 to 10 of 18
  1. #1
    the franchise dogger's Avatar
    Join Date
    Mar 2006
    Location
    The Panhandle
    Posts
    572

    quick question with jetworks mod.

    I have made the decision to install my jetworks mod tomorrow morning. what is the current best installation procedure? I have searched for installation instructions and there seems to be a few differnet types of installs,each with their own routing and tapping and such. The directions that came with the jetworks pro kit say to remove the temp sensor and use that hole for the jetworks, but someone told me that was a bad idea because the jetworks should tap the bottom of the pipe... I will be installing my jetworks and dplate at the same time. Also what is the resistor I need for the sensor bypass on my 06 gpr? I have read that it should be 1k ohm, and also 10k ohm... anyone know hte difinitive answers?

    as always, thanks alot.
    donnie


  2. #2
    MDGPR's Avatar
    Join Date
    Apr 2006
    Location
    MD
    Posts
    238
    +1
    1
    i personally like island racings set up. Its easily understood. Someone has a nice diagram of it somewhere i couldnt find it. anyone know where it is? Carl told me to just zip tie the sensor up with all your other cables on the left side. then find somethign to plug it with. he said i didnt need the cat con sensor chip either.

  3. #3
    Countless # of kits out there, and personally installed on literally dozens of skis built in house, and not 1 report of a problem yet. ( follow the diagram )
    You can tap the pipe on the bottom and use a 90 if you prefer absolutely no performance difference whatsoever plus wait till you see how NEAT the install looks when completed with the diagram.

  4. #4
    the franchise dogger's Avatar
    Join Date
    Mar 2006
    Location
    The Panhandle
    Posts
    572
    so install it based on the directions using the sensor hole i guess....

  5. #5
    hey donnie, don't listen to carl. he just thinks he knows what he's doin!

    can't wait to see your GPR with the jetworks done to it.

    carl- XLT runs great man! haven't put the GPS on it though since it's acting up.

  6. #6
    the franchise dogger's Avatar
    Join Date
    Mar 2006
    Location
    The Panhandle
    Posts
    572
    jetworks is done.... whats wrong with the xlt?

  7. #7
    nothing at all. i just haven't talked to carl since i put everything on!

  8. #8

    Join Date
    Jan 2007
    Location
    Milwaukee, Wisconsin, United States
    Posts
    773
    +1
    1
    which cat replacement should be used? Im ny 12r i had a Dplate. Jet works has a hole in the middle. Rivas is trumpet shaped? Please advise.

  9. #9
    use the R&D D plate.

  10. #10
    Moderator RX951's Avatar
    Join Date
    Apr 2005
    Location
    League City, Texas
    Posts
    16,066
    +1
    23
    both my GPR's have the Jetworks O-plate.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Quick question for FZS mod
    By lukygomes in forum Yamaha PWC Performance (4-stroke)
    Replies: 11
    Last Post: 06-18-2010, 06:04 AM
  2. help with jetworks mod
    By syk1300 in forum Yamaha PWC Performance (2-stroke)
    Replies: 2
    Last Post: 07-16-2008, 10:44 AM
  3. Need a part--and help with Jetworks mod
    By cj1058 in forum Yamaha PWC Performance (2-stroke)
    Replies: 2
    Last Post: 08-06-2007, 08:22 AM
  4. Need a part--and help with Jetworks mod
    By cj1058 in forum Yamaha Old School Skis
    Replies: 3
    Last Post: 08-05-2007, 11:08 PM
  5. Jetworks Mod Question
    By Gipper in forum Yamaha PWC Performance (2-stroke)
    Replies: 5
    Last Post: 02-09-2006, 02:30 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •