Page 1 of 4 1 2 3 ... LastLast
Results 1 to 10 of 31
  1. #1
    05GTXLTD's Avatar
    Join Date
    Jan 2007
    Location
    McKinney, TX
    Posts
    453

    Need a good reputable shop in North Dallas

    I need to find out a good reputable shop hopefully not too far from the McKinney/Richardson/Lewisville area. As y'all know my washers were eaten by the gremlins in the accounting dept. at Sea Doo. So its making me sick not having it out on the water.

    If you can, shoot me the number for the shop too. I'm going on a blitz to get estimates (mostly on the time frame) to get my doo back out there!

    Kyle


  2. #2
    Yamaha tow boat RIDEALLDAY's Avatar
    Join Date
    Feb 2006
    Location
    Texas
    Posts
    1,447
    Try Kawasaki City in Lancaster, 972-228-3772, they are honest and will do a thorough job. I know it's a far drive but don't let that sway you. There are dealers closer but I can't reccommend them personally. Someone said Sherman Powersports? also.
    Good luck, Todd

  3. #3
    05GTXLTD's Avatar
    Join Date
    Jan 2007
    Location
    McKinney, TX
    Posts
    453
    I honestly forgot about sherman powersports until today when I drove by there on my delivery run for work. They seem like good guys from the times I've talked to them. Glad to know they're not considered shady.

  4. #4

    Join Date
    May 2007
    Location
    Lake Texoma, TX
    Posts
    52
    i blew mine and took it to sherman. They ONLY put a new one in no oil change or anything. 0.3 hours latter the motor is LOCKED UP!! I dont trust them much anymore.

  5. #5
    Yamaha tow boat RIDEALLDAY's Avatar
    Join Date
    Feb 2006
    Location
    Texas
    Posts
    1,447
    I had that excact problem at another dealer, just replaced sc and good to go.. 10 minutes later motor locked up - broken cam chain from crap left in the oil system!

  6. #6
    05GTXLTD's Avatar
    Join Date
    Jan 2007
    Location
    McKinney, TX
    Posts
    453
    So basically there's no one around here that's worth taking the machine to huh? Great.....this is such a nightmare to deal with I can't believe it.

  7. #7
    JetSkiDaddy's Avatar
    Join Date
    May 2005
    Location
    Houston, TX
    Posts
    1,418
    +1
    4
    If your willing to travel to Houston Andy Wise will take care of you right.

    AW & Sons
    Andy Wise
    7113 957-3127

  8. #8
    well since we're talking about driving, take it to C&S fun center( right off the highway before you get to witchita falls. Was in Witchita falls, but now a little closer in the town right before Witchita falls). Sam Schaffner used to be a racer, his son used to race (jetskierO) and I highly doubt he'll screw your stuff up. Most of these shops just work on stock stuff, so taking it to someone who knows mods as well is worth the $$. Try calling motion powersports at 214-503-6262 if that's still their #.
    JOE

  9. #9
    JetSkiDaddy's Avatar
    Join Date
    May 2005
    Location
    Houston, TX
    Posts
    1,418
    +1
    4
    Well since were talking about modding ski's and ex racers

    Andy is a well know racer who holds cc world tiltles and also national titles in endurance. He no longer races cc but is still active in Super Coarse and is currently a sponsored ridder and back up mechanic for Noble racing. I am sure he might know just a tad about Modded RXP's You can read up about him here
    http://www.nobleracing.net/RacingTeam/RacingTeam.htm

    ohh ya, Andy just took first place 2 weekends ago out in California at the Clear Lake Super Coarse race

    Also Franko uses him from time to time.

  10. #10
    Moderator Franko's Avatar
    Join Date
    Apr 2005
    Location
    Dallas, Texas
    Posts
    3,829
    +1
    2
    If it were me, I would make the drive to Houston and let Andy do the work. He will do a much better job than any dealer, and probably be cheaper too.

Page 1 of 4 1 2 3 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Need a good reputable crank shop
    By badfast7 in forum Kawasaki PWC Performance (2-stroke)
    Replies: 4
    Last Post: 07-16-2012, 10:18 PM
  2. need help finding a dyno tune shop in north east
    By stingray152003 in forum Open Discussion
    Replies: 9
    Last Post: 05-26-2010, 11:05 AM
  3. I need a good paint shop in PA, NJ, MD area
    By element6 in forum Shops, Tools and Tricks
    Replies: 11
    Last Post: 05-10-2010, 07:06 PM
  4. Need a good parts shop - 1999 Polaris SLTX
    By andytlewis in forum Polaris Open Discussion
    Replies: 13
    Last Post: 07-12-2007, 06:17 PM
  5. Any good repair shops in IL or IA
    By Dragdaddy71 in forum 4-Tec Performance
    Replies: 5
    Last Post: 07-03-2007, 07:45 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •