Page 2 of 7 FirstFirst 1 2 3 4 ... LastLast
Results 11 to 20 of 61
  1. #11
    spud's Avatar
    Join Date
    Jul 2006
    Location
    Oceanside, California
    Posts
    1,348
    +1
    1
    We are looking forward to hearing your results Fercho.

    Art set up my OEM modified to Black Jack 48's and jetted them:

    110 pilots

    2.5 N&S Black 80 gram springs

    150 main jets

    This is to go on a Lowell ported 1390

    I don't know anything about Blackjacks so I am really interested

  2. #12
    Razzbo wil be working straight for 2 weeks so I will have to wait till then

  3. #13
    Moderator RX951's Avatar
    Join Date
    Apr 2005
    Location
    League City, Texas
    Posts
    16,303
    +1
    2
    I've ridden Razzbo's XLT1390 w/Blackjacks...all I can say is tha it HITS ! and its still running rich.

  4. #14
    We need to reinforce that pump tunnel somehow.!!!
    Quote Originally Posted by RX951 View Post
    I've ridden Razzbo's XLT1390 w/Blackjacks...all I can say is tha it HITS ! and its still running rich.

  5. #15
    spud's Avatar
    Join Date
    Jul 2006
    Location
    Oceanside, California
    Posts
    1,348
    +1
    1
    Can we condense this information and make it a sticky, or just make it a stick in the how-to section? I plan to add when the BJ 48 "I" body conversions are dialed in.

    Jetting that has worked very well for me with Fercho's recommendation:

    Lowell ported 1300, single pipe, stock carbs, Prok F/A's, Advent Yam 59

    115 pilots

    2.0 N&S 95 G springs

    135 mains

    Lows 1 turn out

    highs 1.5 turns out


    Stock 1200 choke plates in:

    110 pilots

    1.5 N&S 95 G springs

    120 mains

    Lows 1 turn out
    Highs 1.5 turns out

    Stock 1200 choke plates removed

    110 pilots

    1.5 N&S 95 G springs

    125 mains

    Lows 1 turn out
    Highs 1.5 turns out

    Lowell Ported 1390 single pipe, Blackjack 48 I body carbs, Prok F/A's

    Update: I ran the 1390 at Senator's Wash today. The ski ran great the water level was too low to get any runs in much over 1/4 mile. Temp was about 75 degrees

    115 pilots

    2.0 N&S Black springs

    150 mains

    low screws 1 turn out

    High screws 1 1/2 turns out.

    Ski was crisp and accellerated very hard. There might be additional fine tuning, but this works good.
    Last edited by spud; 03-01-2008 at 11:08 PM. Reason: update to 1390 ported BJ 48 jetting

  6. #16
    Hydrotherapy's Avatar
    Join Date
    Sep 2006
    Location
    The Rock
    Posts
    3,157
    Quote Originally Posted by VOODOO View Post
    Nando, what do you recommend for a 1300 with no to little porting, head, single pipe, stock carbs with F/A's and VF3.
    any ideas for 1300 not ported with d plate and 150 psi head 1200 timming stock reeds,stock carbs with flame arrestors

  7. #17
    WE DONT DIAL 911 RDH's Avatar
    Join Date
    Jan 2007
    Location
    LAKE TRAVIS,, not 4 sissies
    Posts
    1,860
    Quote Originally Posted by Fercho View Post
    1200 GPR single piper ported or not, Flame arrestors, Advent CDI Yam 84 Engine, No accelerator pump

    Stock, Novi modified, Prok Atomizers or RPM modified (Stock Bore)

    110 Pilots
    120 Mains
    1.5 N/s
    95 Gram Spring


    For a Triple Piper 1200 add 20 to the main jets.

    should i keep the same 95 gram spring for triples or go to the 115 ?

  8. #18
    spud's Avatar
    Join Date
    Jul 2006
    Location
    Oceanside, California
    Posts
    1,348
    +1
    1
    I updated an earlier thread to include what I believe to be good Lowell ported 1390 jetting.

    That ski is pulling like a freight train.

  9. #19
    Are the jetting specs provided here still valid? I have a ported 1300 w/Novis I'm ordering jets for.

  10. #20
    cmherrera's Avatar
    Join Date
    Dec 2007
    Location
    Guam
    Posts
    488

    same here

    what jettings, 2000 GPR Novi 48, LH ported 1300 single pipe with jetwork mod, Advent yam 84, Head 150psi,IR case porting, VF3's with spacer, fly F/A.Did I miss anything


Page 2 of 7 FirstFirst 1 2 3 4 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 96 XP stock jetting specs
    By revhardSPX in forum 2-Stroke Performance
    Replies: 1
    Last Post: 08-09-2011, 09:41 PM
  2. Jetting Specs
    By rlharrison60 in forum Polaris Open Discussion
    Replies: 7
    Last Post: 05-19-2009, 10:30 PM
  3. Jetting specs with tripples BB
    By great lakes gpr 1200 in forum Yamaha PWC Performance (2-stroke)
    Replies: 15
    Last Post: 02-10-2009, 07:59 PM
  4. Need stock Jetting specs
    By Itowpolarismatrix in forum 2-Stroke Performance
    Replies: 1
    Last Post: 08-19-2008, 06:17 PM
  5. Jetting specs that I have used
    By Fercho in forum Yamaha PWC Performance (2-stroke)
    Replies: 17
    Last Post: 01-07-2008, 08:21 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •