Results 1 to 7 of 7
  1. #1
    Dragdaddy71 Dragdaddy71's Avatar
    Join Date
    May 2007
    Location
    Moline , IL
    Posts
    126
    +1
    1

    7400 rpm's with new washers?

    Well, I got my Stage 1 RXP supercharger back on and put new plugs in it and a new OEM battery and that got me back out on the water. Jerry just put new washers in it and bearings and the thing runs out good with no misses but now it only will go 65 mph on the speedo and only 7400 rpm.
    It used to peg 70 on the speedo instantly and pulled much harder. I looked at the wear ring and it seems fine. Any other ideas??


  2. #2
    ARNYGOLLOTT3's Avatar
    Join Date
    May 2007
    Location
    Biloxi, MS
    Posts
    810
    Which washers did you replace, and are you sure you put the spring washers back in the correct order?

  3. #3
    Dragdaddy71 Dragdaddy71's Avatar
    Join Date
    May 2007
    Location
    Moline , IL
    Posts
    126
    +1
    1
    Jerry did the swapof the bearings and washers. I just installed the supercharger.

  4. #4
    ARNYGOLLOTT3's Avatar
    Join Date
    May 2007
    Location
    Biloxi, MS
    Posts
    810
    Check hoses and clamps...boost leak?

  5. #5
    Small Craft Advisory Taylor215's Avatar
    Join Date
    Sep 2006
    Location
    Coconut Creek Florida
    Posts
    456
    +1
    3
    Interesting situation. I had the SC washers done(thanks Jerry) and I resintalled the sc myself. I tested yesterday and it runs fine, but only gets up to 66 on gps. I was just a tad faster than my buddies stock 06 RXP. I was getting up to 69+ on GPS before I took the SC out. I am going to tighten down the hoses once more. Oh and rpms's were only 7600 as opposed to 7900 before I did the install.

    I was just wondering where esle I lost the speed from, any ideas....
    Last edited by Taylor215; 07-08-2007 at 12:47 PM. Reason: add info

  6. #6
    Dont judge me...
    Join Date
    Jul 2006
    Location
    FLORIDA
    Posts
    610
    you might have a boost leak... check all of your hoses and clamps

  7. #7
    ADAMBOMB's Avatar
    Join Date
    Mar 2006
    Location
    Sunrise,Florida
    Posts
    4,723
    +1
    196
    Is it fixed now?>

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Low RPM with New Prop
    By Water Pig in forum 4-Tec Performance
    Replies: 11
    Last Post: 06-14-2010, 07:05 PM
  2. FS Machined S/C back half with new bearings and washers
    By bankyf in forum Sea Doo Classifieds
    Replies: 2
    Last Post: 03-13-2010, 04:45 PM
  3. 7400 rpms normal with jerrys washers?
    By battsy in forum 4-Tec Performance
    Replies: 11
    Last Post: 07-30-2007, 09:01 AM
  4. What oil to use with new metal washers?
    By Jarrett in forum 4-Tec Performance
    Replies: 22
    Last Post: 09-09-2006, 05:55 PM
  5. 03 GTX with New S/C ... Still down on RPMs and Speed..?
    By Fast05RXP in forum Sea Doo Open Discussion
    Replies: 3
    Last Post: 07-21-2006, 02:12 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •