Results 1 to 6 of 6
  1. #1
    steved's Avatar
    Join Date
    Sep 2006
    Location
    UK
    Posts
    358
    +1
    14

    VTS trim set up ?

    Sorry if there is a Thread for this but cant find it .

    Rxp with 2 deg wedge and vts rod but looknig today with the trim in the top full up position the nozzle only looks square to the rear of the hull ?

    What is the best way to set this up say ride plate level and vts centre and square to rear , what is the best or proven set up for this .

    Thanks


  2. #2
    steved's Avatar
    Join Date
    Sep 2006
    Location
    UK
    Posts
    358
    +1
    14
    Help,

    There must be an answer out there

    Thanks

  3. #3
    ARNYGOLLOTT3's Avatar
    Join Date
    May 2007
    Location
    Biloxi, MS
    Posts
    810
    I have been told by people with 80+ skis that the best position for trim with a wedge for speed is 'one notch' above neutral...or one above half way....I cannot explain or verify this...yet...but have been told by three 'masters' of RXP speed...hope this helps

    I was also told that setup the VTS rod so that with it in its full up positon it only goest to that point mentioned above...this allows for deep nose whole shots and 'idiot proof' top speed settings...good luck

  4. #4
    steved's Avatar
    Join Date
    Sep 2006
    Location
    UK
    Posts
    358
    +1
    14
    Sounds like a good way to go . Has any one got a Riva VTS rod off that could give me the measurement between hole centres this would prove if mine is set ok .

    Thanks in advance

  5. #5
    vidbuster's Avatar
    Join Date
    Jan 2007
    Location
    Suburban Wasteland, CA
    Posts
    221
    +1
    1
    I've wondered the same thing. I have the same setup and I've been told a few months back to bring the VTS one notch below the top. It should skip one. Thats how I ride now.

    After hours on my ski with the wedge and rod I think that "top" VTS gives too much bounce. I never ride that way.

    Good Luck
    madness

  6. #6
    HORSEPOWER JUNKIE 9secZO6's Avatar
    Join Date
    Jun 2007
    Location
    Belle Chasse, La.
    Posts
    2,006
    +1
    1
    on my 04, this tip is useless, but on my 07, I trim and watch rpm...sweet spot gives me 20-40 rpm..every time. And I have the wedge and rod

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. WTB: manual trim set up
    By shawnIII in forum Sea Doo Classifieds
    Replies: 0
    Last Post: 07-20-2009, 06:35 PM
  2. wtb 2004 gp1300r oem trim set up
    By washo6o4 in forum Yamaha Classifieds
    Replies: 0
    Last Post: 05-23-2009, 01:28 PM
  3. Complete GPR Trim set up
    By mrbtd in forum Yamaha Classifieds
    Replies: 1
    Last Post: 12-16-2008, 07:08 AM
  4. wtb :gpr handlebar trim set up
    By jwbanks in forum Yamaha Classifieds
    Replies: 3
    Last Post: 11-15-2008, 01:25 AM
  5. Dv8Razz & Peteshauling's new set up
    By peteshauling in forum 4-Tec Performance
    Replies: 13
    Last Post: 08-28-2005, 07:32 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •