Results 1 to 4 of 4
  1. #1
    2017 RXT-X 300 zone 5's Avatar
    Join Date
    Jun 2007
    Location
    Lake Luzerne, NY
    Posts
    589
    +1
    8

    Installing the steel washers

    I just finished looking at the 07 shop manual, on this, and I just wanted to make sure that I didn't miss something.

    Is this what is involved? In an under 10 Hr RXT?

    1. Remove SC
    2, Remove nut from shaft.
    3. remove the parts from the shaft (spring washers, drive gear needle bearings etc)
    4. Throw ceramic WASHERS away. Replace with steel ones
    5. replace needle bearings and coat with kluber isoflex grease
    6. put all the parts back on the shaft, and Tq nut down to 22lbs, using red locktite
    7. replace SC and such.
    ready to run.

    is there anything else that I need to do, or is it really as basic as the manual makes it sound?


  2. #2
    Moderator Franko's Avatar
    Join Date
    Apr 2005
    Location
    Dallas, Texas
    Posts
    3,829
    +1
    2
    Forget the Kluber Isoflex. Just use some bearing grease. Other than that, you pretty much got it. Pour some oil on the clutch before you put it back in for safe measure.

  3. #3
    2017 RXT-X 300 zone 5's Avatar
    Join Date
    Jun 2007
    Location
    Lake Luzerne, NY
    Posts
    589
    +1
    8
    Quote Originally Posted by Franko View Post
    Forget the Kluber Isoflex. Just use some bearing grease. Other than that, you pretty much got it. Pour some oil on the clutch before you put it back in for safe measure.
    So just use some good high temp grease on the 40 odd needle bearings, and them when you say clutch, I assume you are talking about the washers and the rest of the assembly?

    With less than 10 hours on it, should I replace the needle bearings and teh spring washers, or just put them back?

  4. #4
    2017 RXT-X 300 zone 5's Avatar
    Join Date
    Jun 2007
    Location
    Lake Luzerne, NY
    Posts
    589
    +1
    8
    and I forgot to add another question. I want to support Green Hulk, but in the on line store they have their washers and Riva's. Is one better than the other or does it not matter, so I would be supporting GH more by buying his washers?

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. YOU Stock air boxs guys. That installed the fan? Questions
    By Water4fire in forum Sea Doo Open Discussion
    Replies: 16
    Last Post: 11-21-2008, 10:57 AM
  2. Finished my Steel Washer install
    By zone 5 in forum 4-Tec Performance
    Replies: 5
    Last Post: 08-22-2007, 05:55 AM
  3. Trying to install the ATM boost guage
    By Phil in forum 4-Tec Performance
    Replies: 5
    Last Post: 09-13-2005, 11:59 AM
  4. Anyone out there installed the RR IC?
    By rx4pain in forum 4-Tec Performance
    Replies: 14
    Last Post: 07-01-2005, 12:01 PM
  5. Installing the vortec Sc What to look for
    By Jrsrxp in forum 4-Tec Performance
    Replies: 5
    Last Post: 05-22-2005, 09:57 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •