Results 1 to 6 of 6
  1. #1
    Dave Sharp dav_dman's Avatar
    Join Date
    Aug 2005
    Location
    louisville Ky/so. IN
    Posts
    1,453
    +1
    1

    what is traction control and disable angle sensor

    1) what is traction control on the newer yami's.. how is it sensored...can we disable it?

    2)where is the angle sensor that shuts it down if the angle is too steep ..how to disable..want to make sure i'm not bothered with all the big brother bs..

    i had a 2001 gpr, but over the winter will get an 05 and want to know about the new stuff added in #1 and #2 above please.

    thank you,
    Dave


  2. #2
    philip_gpr's Avatar
    Join Date
    Dec 2005
    Location
    Canada
    Posts
    2,724
    +1
    3
    me too

    can these two sensors simply be disconnected?

  3. #3
    Moderator RX951's Avatar
    Join Date
    Apr 2005
    Location
    League City, Texas
    Posts
    16,066
    +1
    23
    I am sure somebody can explain this better than me....but from what I experienced on the EFI conversion ski I built, during traction control, the ECU senses a load on the engine by how fast the RPM's rev on the motor. If if revs too fast, such as out of the water on a trailer when you try to blip it, the ECU will cut fuel and timing back in order to bring the revs (rpm) back down. You can not disable the traction control. It is programmed int he ECU.

    The EFI skis can really be noticed with this feature when you try to rev it on a trailer under no load. EFI skis can sound and act weird out of the water. But once it is in the water, the ECU senses the load on the motor and it acts right again.......

    that about right guys ? hope I splained it somewhat right.....




    The slant detector is mounted on the front wall of the inner hull behind the foam. You can disconnect it or just open it and place zip ties on either side of the brass weight. I left mine in and enabled and it never cut the ski off.

    * You can also put a peice of popcorn foam on either side of the brass weight.


    .

  4. #4
    Moderator RX951's Avatar
    Join Date
    Apr 2005
    Location
    League City, Texas
    Posts
    16,066
    +1
    23

  5. #5
    Moderator RX951's Avatar
    Join Date
    Apr 2005
    Location
    League City, Texas
    Posts
    16,066
    +1
    23
    Location, remove front bucket


  6. #6
    Dave Sharp dav_dman's Avatar
    Join Date
    Aug 2005
    Location
    louisville Ky/so. IN
    Posts
    1,453
    +1
    1
    perfect! mucho gracias !!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. What is this ting - and where is it missing?
    By Martinborgesen in forum Kawasaki How To & FAQs
    Replies: 6
    Last Post: 02-02-2015, 10:23 PM
  2. what is the exit and steerring nozzle size range differences, min and max?
    By Pale Rider in forum Yamaha PWC Performance (2-stroke)
    Replies: 11
    Last Post: 08-01-2010, 07:47 AM
  3. what is this ski and what's it worth?
    By ppkarnezis in forum Yamaha Open Discussion
    Replies: 10
    Last Post: 01-27-2009, 03:35 PM
  4. What is this part, and why do I need it??
    By boostaholic in forum Yamaha PWC Performance (2-stroke)
    Replies: 7
    Last Post: 04-30-2008, 12:21 PM
  5. What is a Billion and Taxes!
    By mjammer in forum Open Discussion
    Replies: 6
    Last Post: 02-15-2008, 05:49 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •