Results 1 to 8 of 8
  1. #1

    Join Date
    Jul 2005
    Location
    SE Texas
    Posts
    396
    +1
    2

    Pulling the SC on an 04 GTX ?

    Greetings--

    Any gotchas I need to know about when pulling and reinstalling the SC units on my 04 GTX ?

    I"m going to have the upgraded clutch/shaft installed.

    Thanks--


  2. #2
    Red Devil's Avatar
    Join Date
    Apr 2005
    Location
    Chesterfield/Richmond, VA
    Posts
    1,812

    Re: Pulling the SC on an 04 GTX ?

    Quote Originally Posted by Piney
    Greetings--

    Any gotchas I need to know about when pulling and reinstalling the SC units on my 04 GTX ?

    I"m going to have the upgraded clutch/shaft installed.

    Thanks--
    Be prepared disconnect the J pipe from the manifold to move the waterbox to the rear about 7 inches. Pretty simple after that.

  3. #3

    Join Date
    Oct 2005
    Location
    Ann Arbor, MI
    Posts
    1,439
    Jay,

    Should any torx set have the torx bit you need for the S/C?

    and could someone take some pictures and post up specific instructions for removing the S/C...RIvas are kind of cutting corners...Thanks!

  4. #4
    Red Devil's Avatar
    Join Date
    Apr 2005
    Location
    Chesterfield/Richmond, VA
    Posts
    1,812
    Quote Originally Posted by Totallyblown
    Jay,

    Should any torx set have the torx bit you need for the S/C?

    and could someone take some pictures and post up specific instructions for removing the S/C...RIvas are kind of cutting corners...Thanks!
    AJ,

    Go to Sears and pick up a closed 1/4" ratcheting wrench. I think it is around $5 and is perfect to get that one bolt on the back of the S/C out of there. Any 1/4" socket will work, you don't have to use the torx if you don't have any. There are only 3 screws that hold the S/C in place, one on the back on two on the front.

  5. #5
    Quality work without compromise! Pale Rider's Avatar
    Join Date
    Oct 2005
    Location
    Goldsboro, NC
    Posts
    18,791
    +1
    182
    after you remove the mounting screws, and move waterbox back, assuming you have your air intake duct off, simply pull straight out, try not to twist or turn sideways, don`t want to rub the pto cover with the sharp teeth on the SC... Yeah, just like Jay said! ...PR...

  6. #6

    Join Date
    Jul 2005
    Location
    SE Texas
    Posts
    396
    +1
    2
    I read over the RIVA installation notes-not much deatil there. Quick question-- what is anti-seize compound ? Available from auto parts store or somthing special needed ?

  7. #7
    Vman's Avatar
    Join Date
    Nov 2005
    Location
    NJ
    Posts
    4,360
    +1
    339
    http://www.permatex.com/products/aut...ubricant_a.htm


    Available at your local NAPA auto parts.

  8. #8
    Red Devil's Avatar
    Join Date
    Apr 2005
    Location
    Chesterfield/Richmond, VA
    Posts
    1,812
    Quote Originally Posted by Piney
    I read over the RIVA installation notes-not much deatil there. Quick question-- what is anti-seize compound ? Available from auto parts store or somthing special needed ?
    Just go to Advance or Auto Zone and they usually have them in little "ketchup" size packets at the front of the store for about $1. It says Anti-seize right on the packet. One of those little packets will last you a bunch of impeller changes along with taking care of the supercharger removals.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Pulled the trigger - 2011 GTX iS 215
    By Morphd in forum Sea Doo Open Discussion
    Replies: 6
    Last Post: 07-10-2013, 05:35 PM
  2. looking at pulling the trigger on a 1996 Seadoo gtx
    By reeltime in forum Sea Doo Open Discussion
    Replies: 6
    Last Post: 12-24-2012, 04:59 PM
  3. GTX won't turn off when you pull the key, keeps beeping.
    By FLSUN in forum Sea Doo Open Discussion
    Replies: 5
    Last Post: 04-06-2008, 04:19 PM
  4. Rotax Oil Pressure Jet, necessary to pull the head off?
    By excess in forum 4-Tec Performance
    Replies: 12
    Last Post: 07-01-2006, 10:02 AM
  5. I pulled the motor on my xp
    By ccassone in forum 2-Stroke Performance
    Replies: 1
    Last Post: 03-05-2006, 06:14 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •