Results 1 to 9 of 9

Thread: Not Firing

  1. #1
    fastkaz's Avatar
    Join Date
    Jan 2007
    Location
    Cayman Islands/Orlando Fl
    Posts
    299

    Not Firing

    i have a gp1300r and its not firing..what can cause the problem..i check the sensore from the exhaust to the electrical box and it is connected.


  2. #2

    Join Date
    Jan 2006
    Location
    UK
    Posts
    202
    What did you do last on the ski?

    Have you adjusted the throttle cable? Check that the butterflys shut completely.


    Also are there any error code? hold the dash button down for 10 sec after turning the engine over.

  3. #3
    fastkaz's Avatar
    Join Date
    Jan 2007
    Location
    Cayman Islands/Orlando Fl
    Posts
    299
    i ran it and it flushed it out and went back later to start it and id didnt... no error codes. the butter fly closes properly and no didnt adjust the throttle cable

  4. #4
    Hydrotherapy's Avatar
    Join Date
    Sep 2006
    Location
    The Rock
    Posts
    3,347
    +1
    17
    have you checked the start/stop assembly

  5. #5
    fastkaz's Avatar
    Join Date
    Jan 2007
    Location
    Cayman Islands/Orlando Fl
    Posts
    299
    its roling over fine

  6. #6
    Hydrotherapy's Avatar
    Join Date
    Sep 2006
    Location
    The Rock
    Posts
    3,347
    +1
    17
    Quote Originally Posted by fastkaz View Post
    its roling over fine
    it will roll fine with the start and stop button pressed simultaneously but will not fire,it was just a thought incase the stop/start is shorting out

  7. #7
    WATER WOODY's Avatar
    Join Date
    Aug 2005
    Location
    Minden, Nevada, United States
    Posts
    10,664
    +1
    11
    If the throttle is slightly opened,it will not start.
    ON THE COMPUTER,THERE IS A 2 WIRE CONNECTOR THAT GOES TO THE SLANT DETECTION SWITCH,black/orange and yellow/black,try unplugging the connector and starting it.This will tell you if the switch is bad.

  8. #8
    When you turn it over and it does'nt start does the overheat symbol flash on the cluster?

    I know you say the wire from the exhaust is connected, but which one? There is a cat temp sensor that wont prevent starting but the lower water temp sensor will prevent starting if its not replaced with a resistor. If all else fails you can unplug the water temp sensor and put a resistor in the plug. If that works then you have a bad sensor or broken wire. Its unlikely but it is something else to check.

  9. #9
    fastkaz's Avatar
    Join Date
    Jan 2007
    Location
    Cayman Islands/Orlando Fl
    Posts
    299
    yeh i have in the ater sensor and the othe sensor becaus ei have in the d plate

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Gp1300r tick over but does not fire up. PLEASE anyone help me!
    By Waverider1300 in forum Yamaha How To & FAQs
    Replies: 16
    Last Post: 04-21-2009, 11:07 PM
  2. Cyl not firing
    By brandoneastland in forum Polaris Open Discussion
    Replies: 5
    Last Post: 07-09-2008, 08:55 PM
  3. 1995 SS XI 750 Not Firing.??????
    By twadd10 in forum Kawasaki Open Discussion
    Replies: 10
    Last Post: 07-08-2008, 12:42 PM
  4. seadoo not fireing
    By tbcgroup in forum Sea Doo Open Discussion
    Replies: 1
    Last Post: 04-03-2008, 06:25 PM
  5. Aft cylinder not firing
    By skyler_lloyd in forum Polaris How To & FAQs
    Replies: 1
    Last Post: 07-14-2007, 01:12 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •