Results 1 to 2 of 2
  1. #1
    100 MILES OF HEAVEN AND I AM SMACK IN THE MIDDLE KEYZBUM's Avatar
    Join Date
    Apr 2007
    Location
    JUST NORTH OF CUBA-- FL,KEYS
    Posts
    2,556
    +1
    39

    ?'s on a gp1200 pump shoe install

    ok got a few ?'s on a 98 gp1200 pump and shoe install

    1-- on a new shoe should i pack some/alot of grease in the tube or ?

    2-- is there any alignment to do on the shoe or pump?

    3-- can i install the pump and shoe as 1 or ?

    4-- SHOULD i install the intake grate and then seal it to the shoe,out of the craft,,(big gap at back,, thin line on the sides) is this the same as the r&d Pump Shoe Seal Kit ???

    thanks and sorry so many ?'s
    i wont be a yami nuub forever ----
    mattman


  2. #2
    DAGO RACING CREW 97GPSLEEPER's Avatar
    Join Date
    Apr 2006
    Location
    Orange, TX
    Posts
    4,228
    +1
    169
    .
    Quote Originally Posted by KEYZBUM View Post
    ok got a few ?'s on a 98 gp1200 pump and shoe install

    1-- on a new shoe should i pack some/alot of grease in the tube or ?The manual recommends to pack grease in the tube. If you need to know how much I can look in the manual for you.

    2-- is there any alignment to do on the shoe or pump? Try and get the spacing between the hull and shoe even on both sides. I use 4200 or 5200 and it will squeeze out of the sides of the shoe and fill in the gap between the hull and shoe. After it dries I clean up the excess and make it smooth down the sides of the intake duct/shoe. I install the intake grate to the duct and use a jack to apply pressure to force it as far up as it will go and let it dry.

    3-- can i install the pump and shoe as 1 or ? You can but it becomes a little heavy and cumbersome. I would let the 4200/5200 to dry before I installed the pump.

    4-- SHOULD i install the intake grate and then seal it to the shoe,out of the craft,,(big gap at back,, thin line on the sides) is this the same as the r&d Pump Shoe Seal Kit ??? This is what I do. Good luck.

    thanks and sorry so many ?'s
    i wont be a yami nuub forever ----
    mattman

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Any Directions on how to install Pump Shoe rubber pieces?
    By Dragdaddy71 in forum Yamaha PWC Performance (4-stroke)
    Replies: 3
    Last Post: 05-16-2013, 10:11 PM
  2. Pump shoe installation without alignment tool?
    By 01xdime in forum 4-Tec Performance
    Replies: 16
    Last Post: 05-20-2009, 07:00 AM
  3. pump shoe install question
    By emcewin in forum Yamaha How To & FAQs
    Replies: 10
    Last Post: 02-18-2009, 11:11 PM
  4. Need some Pump Shoe Install Guidance
    By Shibby1485 in forum Yamaha PWC Performance (2-stroke)
    Replies: 11
    Last Post: 04-03-2008, 12:28 PM
  5. pump shoe install ?'s
    By slow1300 in forum Yamaha PWC Performance (2-stroke)
    Replies: 2
    Last Post: 06-29-2007, 01:16 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •