Results 1 to 9 of 9
  1. #1

    Join Date
    Sep 2006
    Location
    topeka,ks
    Posts
    3,332

    gonna block it off i hate not knowing

    my oil pump is going bye bye ,

    what shall i do with the tank , let it be ?

    what to do about the injection points in the carbs ?

    is there any plugs for them ?


    oh and is there a clean way of doing this ? is its gonna all run out ?

    my motor is gonna be in peices for a while


  2. #2
    axgrider73's Avatar
    Join Date
    Feb 2007
    Location
    Southeast Ohio
    Posts
    2,059
    -Drain the oil tank first
    -Use vacuum caps to seal the nipples on the carbs
    -Turn the oil tank into a reserver fuel tank
    -Use a resistor to fool the MFD (if needed)

  3. #3

    Join Date
    Sep 2006
    Location
    topeka,ks
    Posts
    3,332
    i tell you what i think mine are already gone , my guage reeds 3/4 gas and fuel all the time

  4. #4
    axgrider73's Avatar
    Join Date
    Feb 2007
    Location
    Southeast Ohio
    Posts
    2,059
    Are you going to use a block off plate?

    Also, use zip ties to secure the vacuum caps on the carb(s).

  5. #5
    rlharrison60's Avatar
    Join Date
    Aug 2007
    Location
    Orange, Texas
    Posts
    1,091
    +1
    1
    I sealed mine off and pulled the tank. I pulled the gauge from the tank and moved the float about 3/4 up and zip tied it, and layed it to the side by the fuel tank. and used vaccum plugs for the injection points on the carbs.

  6. #6

    Join Date
    Sep 2006
    Location
    topeka,ks
    Posts
    3,332
    im not loveing pwc side of my life , looks like there is gonna be a rebuilt crank in the mix

  7. #7
    Water Bum Rodneyae's Avatar
    Join Date
    Dec 2006
    Location
    Roanoke, Va
    Posts
    3,083
    That dosen't sound good.
    Quote Originally Posted by 97sltx1050 View Post
    im not loveing pwc side of my life , looks like there is gonna be a rebuilt crank in the mix

  8. #8
    gorilla03's Avatar
    Join Date
    Sep 2006
    Location
    stevens point wi
    Posts
    3,774
    +1
    5
    Quote Originally Posted by 97sltx1050 View Post
    im not loveing pwc side of my life , looks like there is gonna be a rebuilt crank in the mix
    ??????? why

  9. #9

    Join Date
    Sep 2006
    Location
    topeka,ks
    Posts
    3,332
    i dont know either i went to winterize then it wouldnt start (starter wouldnt pop out to play ) , fogged everything just for good measure , moved the clys to mix it up .

    come back a week later it wont move for nothing , hasent froze yet keep that in mind ,

    i'v taken the pump out and the domes off , same sad song

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Oil Block off kit or not
    By DaddyT in forum Yamaha PWC Performance (2-stroke)
    Replies: 13
    Last Post: 08-01-2012, 12:15 AM
  2. Replies: 0
    Last Post: 07-30-2012, 12:47 AM
  3. off on switch SHOULD IT BE USED OR not?
    By noshowallgo in forum Yamaha PWC Performance (2-stroke)
    Replies: 7
    Last Post: 10-10-2008, 12:32 AM
  4. GF just called it off
    By Pettee in forum Sea Doo Open Discussion
    Replies: 17
    Last Post: 04-29-2006, 09:07 PM
  5. Parts You May Not Know About
    By MTD03sc in forum 4-Tec Performance
    Replies: 5
    Last Post: 04-08-2006, 12:46 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •