Results 1 to 9 of 9

Thread: Hull Inserts

  1. #1

    Hull Inserts

    where can i get the hull inserts for a rideplate on the SL hull? one of my screws broke the head and the bolt removers wont get i, so i had to bang it out.

    thanks guys


  2. #2
    ph2ocraft's Avatar
    Join Date
    Apr 2006
    Location
    Campbell, Ca.
    Posts
    14,100
    +1
    105

  3. #3
    AWA Member 32DegH2O's Avatar
    Join Date
    Aug 2006
    Location
    Minneapolis, Mn.
    Posts
    2,008
    +1
    5
    Are you going to reuse the same hole as the old insert or are you going to put a new one in a few inches away?

  4. #4
    I would like to re-use the original hole. When i actually hammer or tap the insert in I was going to reinforce it with a little epoxy/thickener just to make sure water wouldn't find its way past the insert.

    -That website is loaded!! None look quite like the one I have, should I
    use a capped one or an open thread?

  5. #5
    AWA Member 32DegH2O's Avatar
    Join Date
    Aug 2006
    Location
    Minneapolis, Mn.
    Posts
    2,008
    +1
    5
    Can you put a link to the part you found...like you said the site is loaded and searching for it might take a bit. Just make sure you use the right stuff to seal it in place.

  6. #6
    not sure this will work here is the Part number 91316A215

    i usually use West Systems Slow hardener with their high density filler i haven't had any of those break.....ever

  7. #7
    AWA Member 32DegH2O's Avatar
    Join Date
    Aug 2006
    Location
    Minneapolis, Mn.
    Posts
    2,008
    +1
    5
    I would go with a capped one.

  8. #8
    She likes the bike. But the ski gets her wet!!!! xlint89's Avatar
    Join Date
    Oct 2006
    Location
    Cleveland OH
    Posts
    17,328
    +1
    29
    I have factory inserts sitting on my bench you can have. PM me your address and I'll send you a few when I get back home.

  9. #9
    AWA Member 32DegH2O's Avatar
    Join Date
    Aug 2006
    Location
    Minneapolis, Mn.
    Posts
    2,008
    +1
    5
    Quote Originally Posted by xlint89 View Post
    I have factory inserts sitting on my bench you can have. PM me your address and I'll send you a few when I get back home.
    This would be the best thing to use!!!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. In need of hull insertion tool
    By xplayer2885 in forum Polaris Open Discussion
    Replies: 5
    Last Post: 04-01-2009, 10:01 PM
  2. do i need to replace my hull inserts?
    By jafo9 in forum Yamaha PWC Performance (2-stroke)
    Replies: 6
    Last Post: 01-23-2009, 03:28 PM
  3. hull insert tips
    By 785 lugs in forum Polaris Open Discussion
    Replies: 5
    Last Post: 05-03-2008, 04:33 AM
  4. Loose Hull Insert for Motor Mount
    By superd in forum Yamaha Old School Skis
    Replies: 7
    Last Post: 10-08-2007, 12:12 PM
  5. XLL/XLT Jim's/IR Ride Plate and hull Inserts
    By snowrunner in forum Yamaha PWC Performance (2-stroke)
    Replies: 3
    Last Post: 03-04-2007, 08:56 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •