Page 1 of 2 1 2 LastLast
Results 1 to 10 of 12
  1. #1

    Join Date
    Jun 2006
    Location
    Fredericksburg, virginia
    Posts
    152

    please can some one help???? " rotax thru hull "

    ok i have the rotax thru hull exhaust and the directions they gave me are very little and they got wet and it killed the picture they gave on how to measure it and i saw the rive templet and was woundering either can some on get me the old picture i could print out or tell me if the rive intal is the sam as the rotax instal because it tells you nothing bout moving the vts system on the rotax install sheet so could some one please help me i really need this cus i wanna go out this weekend thank you
    tommy


  2. #2
    Fast-XPL's Avatar
    Join Date
    Jun 2005
    Location
    Colorado
    Posts
    793
    +1
    20
    I posted my installation and the difference between RR and Riva. Go to this link, page 2 about half way down are my step by step instruction.

    http://www.greenhulk.net/forum/viewt...r=asc&start=25

  3. #3

    Join Date
    May 2006
    Location
    Cincinnati
    Posts
    697
    +1
    3
    do you have to remove the block offs to tighten the rear clamps down??

    also I thought the RR came with a templet like the riva?? If not, thats scary for me to cut into! I need the no brainer riva one.

  4. #4
    here are some new instructions to print
    Attached Files Attached Files

  5. #5
    The most interesting man in the world. Nils888's Avatar
    Join Date
    Jun 2005
    Location
    California
    Posts
    4,230
    +1
    1,043
    Quote Originally Posted by rotax racing
    here are some new instructions to print
    Hay Mark!!!!! Can i run the Egast pipe out the front hood!!!!!!!!!

  6. #6
    Site Admin Green Hulk's Avatar
    Join Date
    Apr 2005
    Location
    Morgan City, LA
    Posts
    36,398
    +1
    2,524

  7. #7
    Can this be sticky in the technical for How to install Thru Hull ?

  8. #8

    Join Date
    May 2006
    Location
    Cincinnati
    Posts
    697
    +1
    3
    is there a little room to move the pipe around incase yur hole is a tad off? I"m trying to decide what pipe to buy, I like the RR because its metal, as say the plastic Riva. I heard a few cases of them melting. But the templet on the riva makes install alot less scary for me.

  9. #9
    Fast-XPL's Avatar
    Join Date
    Jun 2005
    Location
    Colorado
    Posts
    793
    +1
    20
    Quote Originally Posted by CarFanatic
    is there a little room to move the pipe around incase yur hole is a tad off? I"m trying to decide what pipe to buy, I like the RR because its metal, as say the plastic Riva. I heard a few cases of them melting. But the templet on the riva makes install alot less scary for me.
    I didn't have much wiggle room at all. I had to cut the pipe to fit for my application. I "may" have measured incorrectly but since it wasn't a no brainer template, I checked at least 4 times to verify my mark. If you look at the thread I posted, It will show where my mark is in relation to the Riva template. I'll post the picture again as soon as I find it.

    Found the pictures.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	hole_location_112.jpg 
Views:	46 
Size:	54.7 KB 
ID:	4253   Click image for larger version. 

Name:	dscf0010_113.jpg 
Views:	53 
Size:	750.3 KB 
ID:	4254  

  10. #10
    Resident Jicky Jack Jeff C's Avatar
    Join Date
    May 2005
    Location
    Twin Cities, MN
    Posts
    1,153
    Fast:

    Am I seeing things, or did you drill the hole about a half a hole too high

    (Last picture)

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Replies: 2
    Last Post: 08-23-2011, 09:51 AM
  2. Can Any one help me PLEASE
    By undertaker1 in forum Polaris How To & FAQs
    Replies: 4
    Last Post: 07-20-2011, 11:11 PM
  3. Replacement Block options - can some one please clarify??
    By ghlenz in forum 4-Tec Performance
    Replies: 2
    Last Post: 07-15-2011, 08:41 AM
  4. Can some one help me id this part?
    By great lakes gpr 1200 in forum Yamaha PWC Performance (2-stroke)
    Replies: 3
    Last Post: 04-29-2006, 08:40 PM
  5. Can some one Post! A little Help Please!
    By Angelse68cal in forum 4-Tec Performance
    Replies: 6
    Last Post: 08-04-2005, 07:57 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •