Page 1 of 2 1 2 LastLast
Results 1 to 10 of 12
  1. #1

    Join Date
    Jun 2007
    Location
    ontario
    Posts
    179

    still getting water

    OK so i got out for my first ride today on my slt 780, I just recently replaced all the intake hose because there was a hole in one and just thoguht i would do the rest was i was in there. Went for a rdie today and there was still alot of water in the hull afterwards when i pulled the plug.

    I have filled the hull before with water and didnt notice any leaks also checked to see if the speedo line was hooked up and it was all good.....any other suggestions of what to do or what to replace.


  2. #2
    ShaneG's Avatar
    Join Date
    Nov 2007
    Location
    Pittsburgh, PA
    Posts
    386
    Thru hull bearing and carrier.

  3. #3

    Join Date
    Jun 2007
    Location
    ontario
    Posts
    179
    Quote Originally Posted by ShaneG View Post
    Thru hull bearing and carrier.

    ok someone else mentioned that when i had the water problem first.....hard to replace??? hard to find????? thoughts ...help..

  4. #4
    ShaneG's Avatar
    Join Date
    Nov 2007
    Location
    Pittsburgh, PA
    Posts
    386
    Super easy.

    You have to take the 4 long bolts off the pump and unattach all the other stuff to pull drive shaft off (steering cable, cooling tube, etc, loosen the clamps on the bearing carrier and the drive shaft and pump stuff should slide out, after that it's the black canvas type material thing with two worm gear clamps loosen them up and it should just come off. One of the easiest things to get at in the hull.

    Look up the service manual on here in the tech section. Should take about an hour to do.

  5. #5

    Join Date
    Jun 2007
    Location
    ontario
    Posts
    179
    is there any way to inspect it to see if its bad or should i just buy one and do it??? are they expensive....where would i get one

  6. #6
    ShaneG's Avatar
    Join Date
    Nov 2007
    Location
    Pittsburgh, PA
    Posts
    386
    let me look on my bench. I may have one, its used but didn't leak.

    PM me I'll go look on my bench.

    Shane

  7. #7

    Join Date
    Jun 2007
    Location
    ontario
    Posts
    179
    Quote Originally Posted by ShaneG View Post
    let me look on my bench. I may have one, its used but didn't leak.

    PM me I'll go look on my bench.

    Shane

    PM sent

  8. #8

    Join Date
    Jun 2007
    Location
    ontario
    Posts
    179
    Quote Originally Posted by ShaneG View Post
    let me look on my bench. I may have one, its used but didn't leak.

    PM me I'll go look on my bench.

    Shane

    PM sent

  9. #9
    ShaneG's Avatar
    Join Date
    Nov 2007
    Location
    Pittsburgh, PA
    Posts
    386
    Anyone know if 750 bearing carrier will work for 780?

  10. #10
    Lake Mead Bum & BTLS Mark starflight's Avatar
    Join Date
    May 2007
    Location
    Boulder City, NV
    Posts
    3,364
    +1
    1
    Quote Originally Posted by ShaneG View Post
    Anyone know if 750 bearing carrier will work for 780?
    Yes it will.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Replies: 6
    Last Post: 12-07-2011, 05:02 PM
  2. Getting water in engine compartment on RXT?
    By steviey2493 in forum Sea Doo Open Discussion
    Replies: 3
    Last Post: 08-13-2007, 08:39 PM
  3. Keep Getting Water In Cylinders
    By ezrider060 in forum 2-Stroke Performance
    Replies: 2
    Last Post: 06-09-2007, 12:21 AM
  4. Easiest way to get Water out "951DI".
    By Water4fire in forum 2-Stroke Performance
    Replies: 8
    Last Post: 06-05-2007, 12:07 AM
  5. Jetworks mod, Can I get water from here?
    By Mongoose in forum Yamaha PWC Performance (2-stroke)
    Replies: 9
    Last Post: 02-15-2006, 12:47 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •