Results 1 to 6 of 6
  1. #1
    PuprleNuprleGPR's Avatar
    Join Date
    Jul 2006
    Location
    Central FL
    Posts
    741

    How do I remove the PPK pieces?

    I want to remove the rubber pieces from my 04's pump shoe and put em in the 07 shoe. Whats the best method for this? They all just have some 5200 dabbed in the voids to hold them in, the shoe was never fully sealed.

    Thanks for any ideas...


  2. #2
    Moderator OsideBill's Avatar
    Join Date
    Mar 2006
    Location
    United States
    Posts
    11,875
    +1
    30
    Good question I would try driving a wood screw into them and pulling them out with pliers, just a thought anyways

  3. #3
    PuprleNuprleGPR's Avatar
    Join Date
    Jul 2006
    Location
    Central FL
    Posts
    741
    Quote Originally Posted by OsideBill View Post
    Good question I would try driving a wood screw into them and pulling them out with pliers, just a thought anyways
    Hmm..either that or maybe apply some heat and use a screw driver and pry from the side? This would be a better alternative to spending 80 bucks on a new kit (the DIY silicone method is a pita and the 04 shoe is a bit beat up)

  4. #4
    yami_rida#26's Avatar
    Join Date
    Oct 2007
    Location
    Cayman Islands
    Posts
    2,112
    yea it is a pain to get out even without the 4/5200 holding them in i took mine out to properly seal my pump shoe and it took about a half and hour but you just have to keep prying with a flat head screw driver and it should come out eventually.

  5. #5
    "Hustler" Inkaddict's Avatar
    Join Date
    Aug 2007
    Location
    NJ
    Posts
    4,712
    +1
    26
    Quote Originally Posted by OsideBill View Post
    Good question I would try driving a wood screw into them and pulling them out with pliers, just a thought anyways
    +1 Ive taken mine out by this method....

  6. #6
    PuprleNuprleGPR's Avatar
    Join Date
    Jul 2006
    Location
    Central FL
    Posts
    741
    Thanks guys, I got the small ones out with an old butter knife and flat-head. The 3 big pieces in the rear were a pain, but I got them out with the screw and pliers method. Ill be putting these in my 07's shoe when I get the tunnel done. Are there any pieces that would be safe to put in before the tunnel work?

    THanks.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Starter broke off inside of motor. How do i remove the stuck piece?
    By dpshook in forum Kawasaki PWC Performance (2-stroke)
    Replies: 6
    Last Post: 03-24-2017, 07:15 AM
  2. Replies: 3
    Last Post: 04-16-2011, 04:12 PM
  3. How do I remove the 06 RXP?
    By mstennes in forum 4-Tec Performance
    Replies: 2
    Last Post: 08-13-2006, 02:01 PM
  4. How do I remove the supercharger???
    By WildBill9000 in forum Sea Doo Open Discussion
    Replies: 7
    Last Post: 05-21-2006, 10:17 PM
  5. how do you remove the opas
    By jonstephens in forum 4-Tec Performance
    Replies: 2
    Last Post: 07-14-2005, 06:07 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •