Page 1 of 2 1 2 LastLast
Results 1 to 10 of 20
  1. #1
    ou812's Avatar
    Join Date
    Jun 2006
    Location
    Riverside,ca
    Posts
    6,210
    +1
    198

    I Might need some assistance @ MB

    How difficult is it to replace the Carbon ring & boot & align the motor in the parking lot?
    I won't have the CR & Boot in time to install it in my ski 'cause it's leaving for the bug on saturday & should be there wed. late noon. Is anyone willing to help me out here? I'm getting mad cavitation out of the hole & the alignment is off too.

    Thanx in advance.


  2. #2
    The ski's have taken a "backseat" to the Corvette DarthAWM's Avatar
    Join Date
    Nov 2007
    Location
    Odessa, TX
    Posts
    5,364
    I have no idea how hard it is(can't be any harder than me working on my ski in the backyard) but I'll have my tool kit there.

  3. #3
    ou812's Avatar
    Join Date
    Jun 2006
    Location
    Riverside,ca
    Posts
    6,210
    +1
    198
    Quote Originally Posted by DarthAWM View Post
    I have no idea how hard it is(can't be any harder than me working on my ski in the backyard) but I'll have my tool kit there.
    Thanx!
    I'll have some tools too. Would ya happen to have an alignment tool?

  4. #4
    SPEED KILLS, BUT YOU GET THERE QUICKER Keddano's Avatar
    Join Date
    Jul 2007
    Location
    Cedar Rapids,Iowa
    Posts
    6,381
    +1
    23
    I'll help out by riding your ski if your ribs are still too sore.Sorry I didn't run into you when I was in Cali,But I catch you at the Bug!

  5. #5
    ou812's Avatar
    Join Date
    Jun 2006
    Location
    Riverside,ca
    Posts
    6,210
    +1
    198
    Quote Originally Posted by Keddano View Post
    I'll help out by riding your ski if your ribs are still too sore.Sorry I didn't run into you when I was in Cali,But I catch you at the Bug!
    Haha, Even if my ribs are OK you can still take a ride one. I'll have both dupont & rxp there.

  6. #6
    The ski's have taken a "backseat" to the Corvette DarthAWM's Avatar
    Join Date
    Nov 2007
    Location
    Odessa, TX
    Posts
    5,364
    Quote Originally Posted by ou812 View Post
    Thanx!
    I'll have some tools too. Would ya happen to have an alignment tool?
    Nope but I have three cases of home brew, I'm sure eventually it will look lined up

  7. #7
    buddydoo's Avatar
    Join Date
    Oct 2005
    Location
    houma
    Posts
    958
    +1
    9
    How bad off is your carbon seal ring and boot,I have both but have been used and are still good and I have o-rings that fit perfect behand the boot to push it up a little for better seal.

  8. #8
    ou812's Avatar
    Join Date
    Jun 2006
    Location
    Riverside,ca
    Posts
    6,210
    +1
    198
    Quote Originally Posted by buddydoo View Post
    How bad off is your carbon seal ring and boot,I have both but have been used and are still good and I have o-rings that fit perfect behand the boot to push it up a little for better seal.
    It's off for sure. I get spray all over the SC from the bottom spraying up.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	S6300201.JPG 
Views:	59 
Size:	1.51 MB 
ID:	76073  

  9. #9
    buddydoo's Avatar
    Join Date
    Oct 2005
    Location
    houma
    Posts
    958
    +1
    9
    Dam that sucks,if it helps I have these part and o-rings and will put them in my truck tonight so I don't forget.How does the the metal seal ring in front of the carbon seal look,I have one that is in good shape.Looks like you ride in salt water.

  10. #10
    ou812's Avatar
    Join Date
    Jun 2006
    Location
    Riverside,ca
    Posts
    6,210
    +1
    198
    Quote Originally Posted by buddydoo View Post
    Dam that sucks,if it helps I have these part and o-rings and will put them in my truck tonight so I don't forget.How does the the metal seal ring in front of the carbon seal look,I have one that is in good shape.Looks like you ride in salt water.
    50-50 salt/fresh
    I haven't looked at the metal seal yet. Can you toss them in just in case I can't get mine in time please?

    So i'll need to get the boot,ring,Oring & metal seal to be safe? Anything else I should get to complete this task?

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Need some help on what might be wrong 2000 gp12r
    By jaxterra in forum Yamaha PWC Performance (2-stroke)
    Replies: 67
    Last Post: 01-28-2012, 09:06 PM
  2. PH20CRAFT.. need some assistance ;)
    By brad148405 in forum Polaris Open Discussion
    Replies: 3
    Last Post: 01-09-2009, 11:23 AM
  3. My first Polaris..might need some help
    By SideFX in forum Polaris Open Discussion
    Replies: 5
    Last Post: 04-18-2008, 12:44 PM
  4. Need some GTX SC Help
    By Jarrett in forum 4-Tec Performance
    Replies: 5
    Last Post: 06-27-2005, 10:35 AM
  5. Need some graphics
    By lawracing in forum 4-Tec Performance
    Replies: 10
    Last Post: 06-02-2005, 10:16 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •