Page 1 of 2 1 2 LastLast
Results 1 to 10 of 18
  1. #1
    JFizzleJR's Avatar
    Join Date
    Aug 2005
    Location
    FL
    Posts
    8,625
    +1
    806

    Error Code P 1681 and 'Key'

    I go to start the ski and 'key' flashes on the dash along with error code P 1681: communication error - instrument cluster message missing. Anyone have any ideas other than checking the fuses? The same key started the machine yesterday..Is it trying to tell me the key isn't fully secure on the DESS post?


  2. #2
    speedskixp's Avatar
    Join Date
    Feb 2008
    Location
    venice fl.
    Posts
    8,117
    +1
    120
    Yes, I think that is what it trying tell you. Mine did that the other day and I unplugged the lanyard , plugged it back in and it hasn't happened since. I would make sure the lanyard and dess are clean and making good contact.

  3. #3
    JFizzleJR's Avatar
    Join Date
    Aug 2005
    Location
    FL
    Posts
    8,625
    +1
    806
    Ok, thanks for the confirmation. I wiggled the sh*t out of the key and it finally started after a few attempts. Now that the fun's over, it's time to get back to the real problem -- P0112

  4. #4
    Sick Puppy's Avatar
    Join Date
    Apr 2008
    Location
    Antigua Caribbean
    Posts
    38
    Had the same prob with p0112. Ran the bike and got a p1202 and limp mode. Unplugged the tops and planked the hole now the bike runs perfect. Now I only have a p0113 cause the tops is unplugged.
    Hope this helps ya

  5. #5
    JFizzleJR's Avatar
    Join Date
    Aug 2005
    Location
    FL
    Posts
    8,625
    +1
    806
    TOPS is one of the two ideas I have left. You're talking about the actual valve on the engine, not the switch mounted to the MPEM, correct?

    I also keep getting this 1681 code and 'key' flashing. It never did that before, even with the engine running like shit since it's origin. I'm thinking of replacing my starter, giving my battery a long charge, and maybe swapping solenoids to see if that clears it up. My gauges keep lighting up as it trys to crank. Then when it won't start, the gauges go out. I hit start again and then the 'key' flashes.

  6. #6
    Sick Puppy's Avatar
    Join Date
    Apr 2008
    Location
    Antigua Caribbean
    Posts
    38
    Yeah talking about the actual tops valve/ solenoid.
    As for your other ghosts I would also check and make sure all the battery terminals and the ground wires on the front of the engine are clean. Also take the battery to be tested or if you have a load tester do it yourself, a low battery will have you chasing all kinds of non existant shit

  7. #7
    JFizzleJR's Avatar
    Join Date
    Aug 2005
    Location
    FL
    Posts
    8,625
    +1
    806
    The battery is a brand new RIVA gel cell Checked all grounds etc. Thanks for the advice.

  8. #8
    Give me a call in the morning I think I can help you out with the problem.

  9. #9
    JFizzleJR's Avatar
    Join Date
    Aug 2005
    Location
    FL
    Posts
    8,625
    +1
    806
    Ok Will, I will You can also E-mail me if you want.

  10. #10
    Have you tried a new MPEM modual yet?? it seems like you have alot of error codes coming up, I would try a new mpem, clear off the ECU and see what happens, some of the codes it is throwing are very strange, just give me a call!!, I will do my best to help!

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 2004 Yamaha GP1300r error code 67 and has a bog at 5500 rpm
    By Boots123 in forum Yamaha PWC Performance (2-stroke)
    Replies: 1
    Last Post: 04-20-2016, 04:30 PM
  2. Spark error codes and messages
    By 02nelsc in forum Sea Doo Spark
    Replies: 11
    Last Post: 03-01-2014, 09:58 PM
  3. Error Code 135 and 132. APS Replaced twice, still gives error code! Help?
    By Radcon15 in forum Yamaha PWC Performance (4-stroke)
    Replies: 2
    Last Post: 09-05-2012, 10:25 AM
  4. urgent help needed error code 1680 and 1517 on a 04 rxp
    By jetskibill9999 in forum 4-Tec Performance
    Replies: 11
    Last Post: 08-26-2011, 10:01 PM
  5. check engine light and error code P0351
    By cawky in forum 4-Tec Performance
    Replies: 16
    Last Post: 03-27-2009, 09:21 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •