Page 1 of 2 1 2 LastLast
Results 1 to 10 of 16
  1. #1

    Question 99sl900 won't run wot

    I just got electrical worked out on the 900 [i think] machine runs terrible 35 to 40 very rough at half throttle sounds like it keeps trying to kick in. I just put a brand new cdi unit the newest part # they made for this machine. the stator is most likely the original. when i try full throttle it seems like it is choklng out new gas in it carbs& jets cleaned twice no junk in carbs any ideas what could be wrong thanx scott


  2. #2
    Click avatar for tech links/info, donation request K447's Avatar
    Join Date
    Jul 2007
    Location
    near Toronto, Canada
    Posts
    36,599
    +1
    1,276
    Have you checked the stator coils with an ohm-meter, as per the Service Manual?

  3. #3
    ph2ocraft's Avatar
    Join Date
    Apr 2006
    Location
    Campbell, Ca.
    Posts
    14,100
    +1
    105
    Any flashing lights on the MFD?
    LoPor, FUEL, anything??

  4. #4
    www.springbreak-florida.com rgard32's Avatar
    Join Date
    Dec 2006
    Location
    Saint Petersburg,Florida
    Posts
    665
    whats the part # on the cdi you bought? because they made a cdi/stator upgrade kit for that boat...

  5. #5
    the part# is the same as the new cdi that comes with the stator upgrade kit I bought it seperate the dealer told me they were compatible??? and i did not get a manual with the machine thanks

  6. #6
    flashing light on the trim meter in the center and keeps going back to hot cant get mfd to reset

  7. #7
    www.springbreak-florida.com rgard32's Avatar
    Join Date
    Dec 2006
    Location
    Saint Petersburg,Florida
    Posts
    665
    did anyone check timing AFTER they installed the update kit???

  8. #8

  9. #9
    whomever sent the pm please do again i tried to open it in anew window and and it wont let me ilost it i will open it in this window thanx for the help

  10. #10
    ph2ocraft's Avatar
    Join Date
    Apr 2006
    Location
    Campbell, Ca.
    Posts
    14,100
    +1
    105
    Quote Originally Posted by bodefan08 View Post
    flashing light on the trim meter in the center and keeps going back to hot cant get mfd to reset
    The HOT is keeping you in limp home mode.
    Disconnect the tan wire from the temp sensor to the electrical box JUST to test if that solves your problem and let us now.
    If it does, you need to verify IF you have an over heat issue or a bad sending unit, possibly even a pinched or shorted wire.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 07 RXP will not idle and won't run wot.
    By hotrod1983gt in forum 4-Tec Performance
    Replies: 7
    Last Post: 06-13-2014, 09:02 AM
  2. Won't run...wire was toasted
    By hummbusa in forum Polaris Open Discussion
    Replies: 49
    Last Post: 07-28-2009, 04:53 PM
  3. 250X low speed miss morphs into now it won't run
    By reallybigboat in forum Kawasaki PWC Performance (4-stroke)
    Replies: 40
    Last Post: 02-12-2008, 03:13 PM
  4. My Ultra 250 won't run HELP!!!!
    By JMC383 in forum Kawasaki PWC Performance (4-stroke)
    Replies: 32
    Last Post: 07-05-2007, 10:52 PM
  5. 05 Stage 3 Riva Won't Run
    By WannabeGoing80 in forum 4-Tec Performance
    Replies: 18
    Last Post: 04-30-2007, 12:08 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •