Results 1 to 6 of 6
  1. #1
    SoFlaRiders Member mksmi's Avatar
    Join Date
    Jul 2007
    Location
    Tamarac,FL (south Florida)
    Posts
    622

    Help, Where can I get hose fittings?

    I am installing my bilge pump and I need a 90 degree 3/4 to 3/4 hose barb fitting to run my hose. I CAN NOT FIND THEM ANYWHERE !!!. I have been to Home Depot, Lowes,small hardware stores and I have been looking on line every where. Does anyone know a place or a web site that has them. THANK YOU.


  2. #2
    captain obvious Lurker's Avatar
    Join Date
    Jul 2005
    Location
    Visalia, Ca
    Posts
    2,316
    I don't think one is made, here is a T you can just block off one end of the T.

    www.mcmaster.com
    91355K54
    Brass Barbed Hose Fitting Tee for 3/4" Hose ID
    In stock at $8.78 per Pack

  3. #3
    fabrication guru rapidacceleration's Avatar
    Join Date
    May 2005
    Location
    Lake Travis austin, TX
    Posts
    1,156
    +1
    2
    they got plastic 90 in 3/4 size at tractor supply.
    let me go dig in the garage, i might have one for ya..

    if not im going to TSC tomorrow for bolts, ill see if i can pick one up for ya.

  4. #4
    fabrication guru rapidacceleration's Avatar
    Join Date
    May 2005
    Location
    Lake Travis austin, TX
    Posts
    1,156
    +1
    2

  5. #5
    AKA: Larry lafjax's Avatar
    Join Date
    Jul 2006
    Location
    Jacksonville, Fl
    Posts
    3,032
    Quote Originally Posted by mksmi View Post
    I am installing my bilge pump and I need a 90 degree 3/4 to 3/4 hose barb fitting to run my hose. I CAN NOT FIND THEM ANYWHERE !!!. I have been to Home Depot, Lowes,small hardware stores and I have been looking on line every where. Does anyone know a place or a web site that has them. THANK YOU.
    Same problem...I took a sweat copper 1/2" elbow and clamped the 3/4 hose to it. I didn't have much room so I used the copper elbow cause they are very short and I couldn't find a 3/4" plastic elbow.
    See first picture:
    http://greenhulk.net/forums/showpost...&postcount=198

  6. #6
    SoFlaRiders Member mksmi's Avatar
    Join Date
    Jul 2007
    Location
    Tamarac,FL (south Florida)
    Posts
    622
    Thanks for the help guys. Rapidacceleration I think i am going to order two from the fastfitting site you found,they look the best I have seen. If they don't work I think it will be lafjax's set up. Thanks again for the fast replies.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Replies: 19
    Last Post: 05-19-2012, 05:07 AM
  2. where can i get these please help
    By hydrojunkie in forum Yamaha PWC Performance (2-stroke)
    Replies: 6
    Last Post: 08-05-2010, 09:28 PM
  3. Need a water injection fitting, where can I get it?
    By Yamanube in forum Yamaha PWC Performance (2-stroke)
    Replies: 3
    Last Post: 03-27-2009, 09:38 AM
  4. where can I get a quick disconect for flushing?
    By CarFanatic in forum Sea Doo Open Discussion
    Replies: 4
    Last Post: 06-19-2006, 11:32 AM
  5. Where can I get Hi Res Shoots of SeaDoo's??
    By 1 FAST VE in forum Sea Doo Open Discussion
    Replies: 7
    Last Post: 09-14-2005, 11:36 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •