Page 1 of 2 1 2 LastLast
Results 1 to 10 of 14
  1. #1
    LAZBUSA's Avatar
    Join Date
    Apr 2008
    Location
    Palm beach
    Posts
    193
    +1
    4

    Well Got An Rxp Motor For A Conversion

    Well Got The Motor For The Convertion All I Need Is A Gpr Hull And If Any Body Can Give Me A List Or Link To All The Stuff Am Gona Need For This Build Sense I Know There Is A Lot Of People On Here That Done It All Ready Will Apreciate All The Help I Can Get Thanks


  2. #2

    Join Date
    Feb 2006
    Location
    Birmingham AL
    Posts
    2,924
    +1
    2
    I hope you have more than just the motor....

    You need the motor, electronics, fuel tank, guages, wiring harness,, I am sure i am forgetting something but this is just an FYI.

  3. #3
    Fat Man, Little Boat Region8Ultra250X's Avatar
    Join Date
    Jun 2007
    Location
    Jersey
    Posts
    5,563
    +1
    169
    Quote Originally Posted by Green Hulk View Post
    Complements of Mark (Hydrotoys)
    This list can change so check the following link for updates
    http://www.hydrotoys.com/vbforum/showthread.php?t=815

    Rxp Parts:
    • Complete Engine and wiring harness.
    • Gas Tank, 4 straps, 2 brackets,vents, and Pump.
    • Driveshaft for mid-shaft conversion
    • Main wiring harness.
    • Handlebar wiring harness.
    • Gauge and wiring harness.
    • Speedo and internal wiring. Cut 6" from connector.
    • Battery and cables.
    • PEM and bracket and sensors.
    • Temp sensor/buzzer
    • Switch housing.
    • Rear RXP engine mounts.
    • J-pipe and hoses
    • motor mount shims.
    • All the hoses.
    • Throttle Cable and finger or thumb Throttle.
    Gpr Parts:
    • GP12/13R Hull/Topdeck/Steering/Body panels/seat.
    • The GP800R hull has mounts in the wrong place, and hasn't been done yet.
    • 2000-2001 intermeddiate shaft.
    • Motor mount shims
    • Speedo and hull feedthru.
    • Entire pump tunnel. (2005 pump system is preferable)
    • 2" pump spacer and hardware.
    • 2" extension on steering and trim.
    • Gas tank vent system.
    Aftermarket:
    • 2 bar grate. Either 800 or 1200.
    • Stock, R&D or Riva rideplate, modded for 1300r use.
    • TDR waterbox. Model MC-1
    • Riva 1300r free flow hose.
    • Solid front mount.
    • Oil catch can and fitting.
    • Rapid Accelerations Open Loop cooling plate and adaptor.
    • Jegs 2 gauge battery cable kit.
    • Pump Tunnel re-inforcement
    • Pressure relief valve. Either jetworks valves or drilled shoe.
    • Turn nozzle recommended.
    Conversion parts:
    • Engine Mounts
      • Material:
        1/4" Thickness
      • 304L: Common or 316L: Common in Marine.
      • Wire: AWS E/ER308 or 312 welding wire.

      • Amount: All in 1/4"SST
        Front mount:
        Left side:2" bar x6L"
        Right side:2" bar x6L"
        mid-support:2"x2" x14.2L" angle
      • Rear Port:
        top 2" bar x6L"
        bottom 2" bar x6L"
      • Rear starboard:
        Top 2" bar x 8L"
        Bottom 2"x3"angle x6L"
      • Tri-Mix Shielding gas
    • Mid shaft:
      • RXP driveshaft.
      • 2000-2001 intermeddiate shaft.
      • 2-6 week turn around time.
      • See midshaft contact post.
    • Battery tray support:
      • 1/8"x1"x1" L-bracket. Approx 3ft.
      • 1/8"x2"x2" L-bracket. Approx 1ft.
      • Rubber mat.
      • M6x30mm bolt.
      • Sheet SST metal 3"x8"
    • Mid-shaft support bearing support.
      • 1/8" aluminum plate, approx 6"x 10"
      • Bent to L-shaped bracket.
      • Water-feedthru pipe.
    • Air Intake.
      • 4"
        • SC size converter.
        • 4" x9" K/N filter.
        • 4" x6" straight piece.
        • 2x 4" clamps.
        • 1x 3" clamp.
        • gpr flexible tubing from front air intake to rear of ski.
      • Or the Riva RXP 3" system bolts right on.
    • Gas Tank
      • 2" coupler for filler hose.
      • Extra clamp.
      • Bottom corners of "front" of the rxp tank (which sits in hull backwards) need to be heat fitted to the hull.
      • RXP vent system (in/out seperate vents)
    While this list isn't perfect, you should be pretty close if you have all of these parts for the basic Vigilante.

    Updated 3/22/8

    To upgrade to a stage 2 or 3, you will need to make an intercooler mounting system.
    ....

  4. #4
    R rated's Avatar
    Join Date
    Nov 2006
    Location
    Bayville NJ
    Posts
    502
    +1
    8
    i have a gpr1300 for sale with blown motor that we will be parting out .

  5. #5
    LAZBUSA's Avatar
    Join Date
    Apr 2008
    Location
    Palm beach
    Posts
    193
    +1
    4
    Quote Originally Posted by Lvnspeed View Post
    I hope you have more than just the motor....

    You need the motor, electronics, fuel tank, guages, wiring harness,, I am sure i am forgetting something but this is just an FYI.
    I HAVE ALL THAT COMES WITH THE RXP THANKS FOR THE INFO

  6. #6
    LAZBUSA's Avatar
    Join Date
    Apr 2008
    Location
    Palm beach
    Posts
    193
    +1
    4
    Quote Originally Posted by Region8Ultra250X View Post
    ....
    THANKS FOR THE LIST THAT SHOULD KEEP ME BUSY WHERE CAN I GET THE TDR waterbox. Model MC-1 AND WHO IS THE GUY WHO DOES THE SHAFTS?

  7. #7
    Fat Man, Little Boat Region8Ultra250X's Avatar
    Join Date
    Jun 2007
    Location
    Jersey
    Posts
    5,563
    +1
    169
    Quote Originally Posted by LAZBUSA View Post
    THANKS FOR THE LIST THAT SHOULD KEEP ME BUSY WHERE CAN I GET THE TDR waterbox. Model MC-1 AND WHO IS THE GUY WHO DOES THE SHAFTS?

    call TDR and order the box from them


    Contact Ted Thompson at 602-418-2109 and leave your name and contact number for him to reach you.

    The actual price will vary depending on how many he can do at one time.

    You will need:
    • RXP driveshaft with the engine side splines in PERFECT condition.
    • 2000-2001 GPR intermediate shaft. 66V-51323-01-00
    I think you can buy a new intermediate shaft is about $170 from www.boats.net , and a whole lot less used. The 2002 and up gpr shaft will not work for this conversion.

  8. #8
    LAZBUSA's Avatar
    Join Date
    Apr 2008
    Location
    Palm beach
    Posts
    193
    +1
    4
    Quote Originally Posted by Region8Ultra250X View Post
    call TDR and order the box from them


    Contact Ted Thompson at 602-418-2109 and leave your name and contact number for him to reach you.

    The actual price will vary depending on how many he can do at one time.

    You will need:
    • RXP driveshaft with the engine side splines in PERFECT condition.
    • 2000-2001 GPR intermediate shaft. 66V-51323-01-00
    I think you can buy a new intermediate shaft is about $170 from www.boats.net , and a whole lot less used. The 2002 and up gpr shaft will not work for this conversion.
    thanks a lot i got an 01 intermediate shaft here sense i own 2 gprs 00 and a 01

  9. #9
    ecpChris's Avatar
    Join Date
    Jul 2007
    Location
    ocean county nj
    Posts
    2,912
    +1
    427
    Quote Originally Posted by R rated View Post
    i have a gpr1300 for sale with blown motor that we will be parting out .
    rudy i may be interested in this whole ski. let me know and maybe we can work something out
    what year?

  10. #10
    "Hustler" Inkaddict's Avatar
    Join Date
    Aug 2007
    Location
    NJ
    Posts
    4,712
    +1
    26
    .
    Last edited by Inkaddict; 07-15-2008 at 07:40 PM. Reason: .

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Anyone looking for an RXP motor? 2007 4hrs $3500
    By boostaholic in forum Sea Doo Classifieds
    Replies: 6
    Last Post: 08-09-2008, 01:54 AM
  2. Boy, if I only had an RXP motor.
    By KirkF350 in forum Conversion PWC Performance Skis
    Replies: 12
    Last Post: 11-01-2007, 07:29 PM
  3. good deal on a rxp motor for someone building a gprxp
    By Shibby1485 in forum Conversion Skis Classifieds
    Replies: 1
    Last Post: 10-03-2007, 08:52 PM
  4. i know this cant happen but an rxp motor in a superjet
    By spyder3000gtvr4 in forum Conversion PWC Performance Skis
    Replies: 3
    Last Post: 08-23-2007, 10:39 PM
  5. Anyone got a RXP dash for sale??
    By CRS in forum 4-Tec Performance
    Replies: 2
    Last Post: 08-28-2005, 08:05 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •