Results 1 to 6 of 6
  1. #1
    FrankieV123's Avatar
    Join Date
    Aug 2008
    Location
    Florida -JERSEY
    Posts
    260
    +1
    1

    Just bought NEW RXP-Xs couple ?s

    So Monday went over to Riva South in Key Largo and picked up 2 RXPXs....goin to put em in water today....nethin i should no... ne special tricks or should i break em in normally? what should i look out for if i hear nethin out of the ordinary? cant wait to get to feel the acceleration after break in!


  2. #2
    Site Admin Green Hulk's Avatar
    Join Date
    Apr 2005
    Location
    Morgan City, LA
    Posts
    36,398
    +1
    2,524
    Congrats on the new skis and welcome to the forum

    Break them in like you would normally ride them. Don't be afraid to go WOT for short periods during the break in. Vary the throttle for the first few hours.

    Don't break them in with the learning key.

  3. #3

    Join Date
    Apr 2008
    Location
    Miami Beach, Florida
    Posts
    81
    how much did it cost ya?

  4. #4
    RIDE 'EM LIKE YOU STOLE 'EM

    make sure you run high octane, make sure the plugs are in, make sure you get a anchor( dont "beach" the ski) make sure u flush the ski's get a quick connector it makes it easier and spray the rear and the engine down with crc-656 get the salt off especiall but after ride maintenence is HUGE and wipe the plastic chrome off after u ride or they will get water stains if u care dont rune em in water below 3 feet deep if u can

  5. #5
    FrankieV123's Avatar
    Join Date
    Aug 2008
    Location
    Florida -JERSEY
    Posts
    260
    +1
    1
    so 2 days of riding i got almost 5 hours on em. wish i coulda rode more but had to run to key west to go shopping for the girls....yea i noticed if water comes over the hood...salt spots end up on the motor...i was wonddering just spray directly into the motor compartment...after its cool of course?

  6. #6
    R88ory RXP's Avatar
    Join Date
    Feb 2008
    Location
    Kent, England
    Posts
    2,737
    +1
    46
    Not sure if the x seat is the same as mine but i filled the little holes in the bottom of the seat. The plastic bit that sits above the engine when the seat is installed. Jus filled em with some silicon, this stoped the water from dripping on my engine. worth doing if you ride in the sea it stops the salty stuff gettin on all the electrics and engine. R88

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Just Bought a RXP-X
    By phoenixcustoms in forum Sea Doo Open Discussion
    Replies: 6
    Last Post: 05-16-2008, 05:52 PM
  2. Just bought an RXP let the modding begin!
    By greeksupra in forum 4-Tec Performance
    Replies: 12
    Last Post: 05-05-2008, 10:27 PM
  3. Just bought an RXP... extreme newb, help!
    By konabiker47 in forum 4-Tec Performance
    Replies: 7
    Last Post: 06-08-2007, 09:25 AM
  4. just bought my RXP
    By BlaZinMJ in forum Sea Doo Open Discussion
    Replies: 6
    Last Post: 08-16-2006, 09:48 PM
  5. so i just bought an rxp....now some mod's
    By BlaZinMJ in forum 4-Tec Performance
    Replies: 7
    Last Post: 08-12-2006, 09:16 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •