Page 1 of 2 1 2 LastLast
Results 1 to 10 of 14
  1. #1
    JFK
    Join Date
    Dec 2007
    Location
    The Netherlands
    Posts
    21

    Where to get a complete jetworks kit ?

    Several of you are all been very positive about the so called Jetworks kit,
    i found the topic to install it - Now to find the place to purchase it as a kit - note: needs to be willing to ship it abroad to The Netherlands.....

    http://greenhulk.net/forums/showthread.php?t=24493

    Together with the pump reinforcement its a must have for an 08 GPR??
    Other must have is the Leo hole shot kit ?

    Speed for me would be ideal around 70 mph ( as long as i am quicker than a stock SHO ) Now the trick :

    What to mod besides they above to keep up with that tremendous accelaration of the SHO ?,


  2. #2
    yami_rida#26's Avatar
    Join Date
    Oct 2007
    Location
    Cayman Islands
    Posts
    2,112
    Islandracing. (Islandracing.net)

  3. #3
    Mike's GPR's Avatar
    Join Date
    Mar 2008
    Location
    Carol Stream, IL
    Posts
    2,044
    +1
    20
    You could piece the kit together or I believe you can get a complete kit from Island Racing. Riva may also have a complete kit.

    Look at the Jetworks install in the how to section. It will give you an idea of what is needed. It took me a little time to actually figure out what the hell is going on with this mod. But it is pretty easy once you understand it.

    Parts you will need include:
    JW valve
    stealth mod fitting
    pump plate with 90 brass connection
    tubing
    1/2" to 3/8" reduction fitting
    JW gasket
    2 additional 90 brass connections

    You will need to drill and tap two holes on the stinger pipe
    Plug the temp sensor hole in stinger pipe

    I may be missing some of the details, but its covered pretty well in the how to section.

  4. #4
    Moderated
    Join Date
    Oct 2006
    Posts
    3,711
    what mods?

    cut your head for 150psi comp ( ask jim about this)
    ff plate ( also from jim) or get a shred if you ride open water
    vf3 reeds with spacer ( islandracing)
    efi controller ( online store)
    3 degree keyway ( island racing
    air mods ( use the search button) and install an after market bilge if you do these just to be safe
    1200 dual bar intake grate
    pump tunnel reinforcement kit ( a must do mod)
    seal your pump shoe and install a PPK along with it



    You can get a 08 1300 to 70 with just a FF plate, sealed shoe and some air mods but it wont have the torque you want , only reeds, cut head and controller will help get you there with a keyway. with the above mods you should hit 75 with ease. ok so i have gone a bit over the top of what you wanted but hey thats what this place is all about

    there is probably a few other things you will need as well but i will let the pro's chip in their 2 cents.

  5. #5
    2000 GPRXP 4tec shooter98xpl's Avatar
    Join Date
    Dec 2005
    Location
    Charleston SC
    Posts
    2,717
    +1
    3
    WFO on the boards sells the kits as well I believe. So you have several options to choose from.
    SHOOTER

  6. #6
    Ramps's Avatar
    Join Date
    Jan 2008
    Location
    Myakka, FL
    Posts
    649
    +1
    28
    Remember this will only help hole shot. It will reduce (almost elliminate) water in the box.
    I have one installed and I like it. Especially when I am in surf, it seems to keep me more balanced....

  7. #7
    blowbyu's Avatar
    Join Date
    Jun 2006
    Location
    San Antonio, TX
    Posts
    635
    How are you guys running the holeshot kit without heating up the waterbox during extended idle periods? Do the grp's have any type of water injection at the stinger to aid in the waterbox heating up?

    --Robert

  8. #8
    yami_rida#26's Avatar
    Join Date
    Oct 2007
    Location
    Cayman Islands
    Posts
    2,112
    Quote Originally Posted by blowbyu View Post
    How are you guys running the holeshot kit without heating up the waterbox during extended idle periods? Do the grp's have any type of water injection at the stinger to aid in the waterbox heating up?

    --Robert
    Just blip the throttle above the 3500 rpm range every now & then...

  9. #9
    If your not doing something, its hard to screw up. stlouisramsfan's Avatar
    Join Date
    Jul 2007
    Location
    Pontoon Beach Illinois
    Posts
    1,115
    I bought mine from island....
    Here is a deal for the kit.... CHEAP!
    http://www.parkeryamaha.com/jetworks...dapterkit.aspx

  10. #10
    Tool Bag water worx's Avatar
    Join Date
    Aug 2006
    Location
    Sunny Fla
    Posts
    1,925
    +1
    66
    Quote Originally Posted by blowbyu View Post
    How are you guys running the holeshot kit without heating up the waterbox during extended idle periods? Do the grp's have any type of water injection at the stinger to aid in the waterbox heating up?

    --Robert
    Very little heat at idle.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Where to get a Jetworks kit for the 1200r
    By Highlifeking in forum Yamaha PWC Performance (2-stroke)
    Replies: 2
    Last Post: 04-27-2014, 12:54 PM
  2. Where to get Decal/Graphics kits STX-R, Ultra 150
    By cconigliaro in forum Kawasaki Open Discussion
    Replies: 4
    Last Post: 03-04-2012, 12:44 AM
  3. SL750 Triple outlet fule pump kit - where to get?
    By RPOLS3 in forum Polaris How To & FAQs
    Replies: 1
    Last Post: 07-20-2010, 11:42 AM
  4. Where to get an 05 Pump kit?
    By Super in forum Yamaha PWC Performance (2-stroke)
    Replies: 11
    Last Post: 06-05-2006, 08:01 PM
  5. Where to get...?
    By GeoRXT in forum Sea Doo Open Discussion
    Replies: 4
    Last Post: 05-16-2006, 11:03 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •