Results 1 to 9 of 9
  1. #1
    Altezza01's Avatar
    Join Date
    Jun 2007
    Location
    Destin, FL
    Posts
    1,527
    +1
    13

    jetwoks without thruhull

    how would you install the jetworks without drilling thru the hull? where would the hose with the jetworks valve go and where would the hose on the bottom of the stinger go. i do believe you have to remove the siphon? please more info!!!! thanks (want to go fercho version)


  2. #2
    Greenhulk Grasshopah (DRC) HallPass's Avatar
    Join Date
    Jun 2007
    Location
    Kansas
    Posts
    5,587
    +1
    2
    Quote Originally Posted by Altezza01 View Post
    how would you install the jetworks without drilling thru the hull? where would the hose with the jetworks valve go and where would the hose on the bottom of the stinger go. i do believe you have to remove the siphon? please more info!!!! thanks (want to go fercho version)
    stealth mod.

    how to w/ stealth mod:

    http://islandracingperformance.com/f...read.php?t=337

    not disrespecting you jerry or the moderators, posted that because it is where the thread is.

  3. #3
    Altezza01's Avatar
    Join Date
    Jun 2007
    Location
    Destin, FL
    Posts
    1,527
    +1
    13
    thanks kale.

  4. #4
    Altezza01's Avatar
    Join Date
    Jun 2007
    Location
    Destin, FL
    Posts
    1,527
    +1
    13
    will this work without the stealth fitting???......
    on the back of the stinger there is a hose that dumps water out the right side of the transom plate. if i disconnect that and have it dumping overboard using a water bypass fitting can i connect the bottom jetworks hose to this using somekind of reducer to have the jetwork dump water here?
    then have the top jetworks hose connect to the siphon thruhull but instead of connecting to the siphon have it connected to the plate that will be drilled and tapped with a fitting. then i will be able to take out the siphon on the hull and rely on my electric bilge. will this work?

  5. #5

    Join Date
    Apr 2006
    Location
    South MS
    Posts
    1,095
    I found out the hard way. Go ahead and replace the pressure hose all the way from the transom to the jetworks valve. If you use the factory siphon hose it will blow out.

  6. #6
    Altezza01's Avatar
    Join Date
    Jun 2007
    Location
    Destin, FL
    Posts
    1,527
    +1
    13
    Quote Originally Posted by Ronn25 View Post
    I found out the hard way. Go ahead and replace the pressure hose all the way from the transom to the jetworks valve. If you use the factory siphon hose it will blow out.
    yes of course....it wont hold the pressure but will my method work?

  7. #7

    Join Date
    Apr 2006
    Location
    South MS
    Posts
    1,095
    Quote Originally Posted by Altezza01 View Post
    yes of course....it wont hold the pressure but will my method work?
    Sounds like it should work. Just need a pressure line to the jetworks, and a outlet line off the stinger.

  8. #8
    Altezza01's Avatar
    Join Date
    Jun 2007
    Location
    Destin, FL
    Posts
    1,527
    +1
    13
    cool thanks. i'm doing my tunnel reinforcement and i decided while it's out i'm gonna do the jetworks too.

  9. #9
    Greenhulk Grasshopah (DRC) HallPass's Avatar
    Join Date
    Jun 2007
    Location
    Kansas
    Posts
    5,587
    +1
    2
    yeah, take your oem bilge out.. i took my oem bilge out, and just put a rule in there.. and didn't have any problems

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. B-kit with a Rotax Racing ECU without extra fuel STOP NOW!
    By bttek1 in forum 4-Tec Performance
    Replies: 49
    Last Post: 05-16-2006, 04:10 PM
  2. Rivas Stage II without power cooler
    By RXgottaP in forum 4-Tec Performance
    Replies: 1
    Last Post: 04-20-2006, 06:51 AM
  3. Remanufactured motor ran at WOT without Break in.
    By ccassone in forum Sea Doo Open Discussion
    Replies: 8
    Last Post: 03-19-2006, 08:35 AM
  4. Oil Change WITHOUT filter
    By bic1 in forum 4-Tec Performance
    Replies: 5
    Last Post: 01-30-2006, 10:49 AM
  5. Can you have heat fade without RPM loss???
    By 1 FAST VE in forum 4-Tec Performance
    Replies: 1
    Last Post: 08-25-2005, 09:21 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •