Page 1 of 6 1 2 3 ... LastLast
Results 1 to 10 of 57
  1. #1

    R&D SHO/FZR Multi-Pressure Port Boost Gauge/Surge/RRFPR Adaptor

    I got the R&D SHO/FZR Multi-Pressure Port Boost Gauge/Surge/RRFPR Adaptor today and there weren't any instructions in the box. Anyone know how to install this thing?? I really dont even know where it goes...


  2. #2
    mjh3ides's Avatar
    Join Date
    Jul 2007
    Location
    Jupiter, Florida
    Posts
    7,176
    +1
    2,705
    I got mine today...no instructions either. R&D must think we're all pro tuners who don't need them. I'm hoping it will be obvious how to install it once I have the manifold & TB's off.

  3. #3
    Hydrotoys's Avatar
    Join Date
    Jul 2005
    Location
    Mesa, AZ
    Posts
    16,723
    +1
    91
    $60 for a TEE??? Are you shitting me??? What am I missing here?

  4. #4
    Whats that whistling noise? jtskier11's Avatar
    Join Date
    Sep 2007
    Location
    Right side of Kansas
    Posts
    4,342
    +1
    87
    Quote Originally Posted by Hydrotoys View Post
    $60 for a TEE??? Are you shitting me??? What am I missing here?
    Thats bad ass! I need to go to the hardware store, get $10 dollars in parts and charge $50 for all of it it...

  5. #5
    ph2ocraft's Avatar
    Join Date
    Apr 2006
    Location
    Campbell, Ca.
    Posts
    14,135
    +1
    109
    You're paying 50 bucks for the directions...oh, there were none.
    Looks like more than a "T" though...

  6. #6
    Hydrotoys's Avatar
    Join Date
    Jul 2005
    Location
    Mesa, AZ
    Posts
    16,723
    +1
    91
    no seriously.
    What is this Tee doing special?

  7. #7
    R3_killa's Avatar
    Join Date
    Jun 2008
    Location
    Cayman Islands
    Posts
    348
    I tried using a tee on my set up but what I realized was that was no space for the tee to fit! The vacuum line that connects the map sensor to the manifold is too short. About 2.5inches...give or take. I goin to try and post some pics on how it looks.
    Another way you could use a tee without the R&D adapter is to turn the map sensor upside down then move it to the right and secure it by just using 1 bolt instead of two.. It won't look as neat as the adapter kit but it will work

  8. #8
    R3_killa's Avatar
    Join Date
    Jun 2008
    Location
    Cayman Islands
    Posts
    348

    Instructions

    Quote Originally Posted by allstar71 View Post
    I got the R&D SHO/FZR Multi-Pressure Port Boost Gauge/Surge/RRFPR Adaptor today and there weren't any instructions in the box. Anyone know how to install this thing?? I really dont even know where it goes...
    Unbolt the two 10mm head bolts that support the map sensor to the intake manifold. Unplug the map sensor. Remove the two 5/16 bolts that connect the sensor to the mounting bracket. Place the adapter in-between the bracket and the map sensor. Make sure that the barbed end of the adapter faces down. It should fit through the hole in bracket. Place the supplied o-ring over the vacuum port of the map sensor ( be sure to remove the factory vacuum hose when installing o-ring). Place map sensor facing down through the hole at the top of the adapter. Use supplied bolts that came with the kit. They will take the place of the 5/16 bolts. After that, your al set.

  9. #9
    Whats that whistling noise? jtskier11's Avatar
    Join Date
    Sep 2007
    Location
    Right side of Kansas
    Posts
    4,342
    +1
    87
    Quote Originally Posted by Hydrotoys View Post
    no seriously.
    What is this Tee doing special?
    Its helping to VACUUM money from your pocket........

  10. #10
    It's not the destination, it's the journey!! Rip'nTear SHO's Avatar
    Join Date
    Apr 2008
    Location
    Ft. Lauderdale
    Posts
    4,573
    +1
    1
    Quote Originally Posted by jtskier11 View Post
    Its helping to VACUUM money from your pocket........

Page 1 of 6 1 2 3 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Replies: 2
    Last Post: 07-18-2014, 04:36 PM
  2. FS - Parts '08-'10 SHO/FZR Multi-Pressure Port Boost Gauge/Surge/RRFPR Adaptor Kit
    By ksalles in forum Yamaha Classifieds
    Replies: 7
    Last Post: 03-06-2014, 11:00 AM
  3. vac filter in between BOV and FZR Multi-Pressure Port Boost Gauge/Surge/RRFPR Adaptor
    By peterj59 in forum Yamaha PWC Performance (4-stroke)
    Replies: 3
    Last Post: 09-15-2011, 09:34 AM
  4. FZR Multi-Pressure Port Boost Gauge/Surge/RRFPR Adaptor Kit for 2011 Yamaha FZR
    By peterj59 in forum Yamaha PWC Performance (4-stroke)
    Replies: 4
    Last Post: 09-13-2011, 10:05 AM
  5. FZR Multi-Pressure Port Boost Gauge/Surge/RRFPR Adaptor Kit
    By peterj59 in forum Yamaha PWC Performance (4-stroke)
    Replies: 1
    Last Post: 09-08-2011, 01:01 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •