Page 1 of 2 1 2 LastLast
Results 1 to 10 of 16
  1. #1
    hayabusarider's Avatar
    Join Date
    Oct 2008
    Location
    DFW, Texas
    Posts
    52

    Need exhaust coupler for stinger mod

    I finally got my jetflow valve to open at 3000rpm.
    I burnt up the stinger mod coupler when the jetflow valve came apart on the lake. Boy was that an adventure!!!!!!!!

    Need a place to buy a new one. Ron


  2. #2
    thesepaperwings's Avatar
    Join Date
    May 2007
    Location
    South East Kansas
    Posts
    1,283
    +1
    1
    Any auto parts store. You have to buy a longer section and it is around 20 bucks.

  3. #3
    hayabusarider's Avatar
    Join Date
    Oct 2008
    Location
    DFW, Texas
    Posts
    52
    Quote Originally Posted by thesepaperwings View Post
    Any auto parts store. You have to buy a longer section and it is around 20 bucks.
    Thanks for the advice. dumb question that will be answered when I remove the exhaust. What size O.D. is it? Do you use one clamp on each side? What about sealant ?

  4. #4
    thesepaperwings's Avatar
    Join Date
    May 2007
    Location
    South East Kansas
    Posts
    1,283
    +1
    1
    Don't remember OD. Clamp both sides and clamp the hell out of it.

  5. #5
    btldigger's Avatar
    Join Date
    Feb 2007
    Location
    lebanon tn.
    Posts
    1,641
    If I remember corectly the stinger side is smaller than the waterbox.

  6. #6
    steve45's Avatar
    Join Date
    Feb 2008
    Location
    Texas
    Posts
    5,014
    +1
    285
    I bought mine from http://www.intakehoses.com/

    The hose is 2.25" x 2.0", part # RS225X20X25

    I also bought T-bolt clamps from the same source. I had trouble getting the clamps on and ended up using the next larger size.

    I also cut a large block of high density closed cell foam to fit around the water box and keep it from moving. It all seems to stay together now.

  7. #7
    hayabusarider's Avatar
    Join Date
    Oct 2008
    Location
    DFW, Texas
    Posts
    52
    Thanks for the reply Gents. I will get one on order. I did manage to get the one I had to seal. But I don't trust it.
    steve45, did you buy the 2.5 t-bolt clamps?
    Ron
    Quote Originally Posted by steve45 View Post
    I bought mine from http://www.intakehoses.com/

    The hose is 2.25" x 2.0", part # RS225X20X25

    I also bought T-bolt clamps from the same source. I had trouble getting the clamps on and ended up using the next larger size.

    I also cut a large block of high density closed cell foam to fit around the water box and keep it from moving. It all seems to stay together now.

  8. #8
    thesepaperwings's Avatar
    Join Date
    May 2007
    Location
    South East Kansas
    Posts
    1,283
    +1
    1
    I had to get a new one when I put the TDR in.

  9. #9
    steve45's Avatar
    Join Date
    Feb 2008
    Location
    Texas
    Posts
    5,014
    +1
    285
    I originally bought the 2" and 2-1/4" clamps, but couldn't get them on their respective hose ends. I ended up using the 2-1/4" on the 2" hose end and ordering a 2-1/2" for the 2-1/4" hose end.

    I think the pipes are a little bit oversize. It might have been possible to get the 'correct' clamps on if there were enough room to compress them with pliers, but there isn't. I found I could tighten the larger clamps just fine.

  10. #10
    hayabusarider's Avatar
    Join Date
    Oct 2008
    Location
    DFW, Texas
    Posts
    52
    Thanks steve45. I ordered the hose and 2 of the 2 1/2" hose clamps.
    I hope that works.

Page 1 of 2 1 2 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Needing Exhaust cables for Pro 785
    By skigolfnut in forum Polaris Open Discussion
    Replies: 8
    Last Post: 05-18-2010, 06:35 PM
  2. Need Exhaust parts for 98 GP-760 PLEASE"
    By gutterboy2ca in forum Yamaha PWC Performance (2-stroke)
    Replies: 0
    Last Post: 06-09-2008, 05:32 PM
  3. Shorty and exhaust coupler for RXT
    By bruinsrme in forum Sea Doo Classifieds
    Replies: 10
    Last Post: 04-25-2008, 05:09 PM
  4. Need your help! Need Exhaust Clamp for RXP!
    By Matth3wJL in forum 4-Tec Performance
    Replies: 8
    Last Post: 06-04-2007, 02:21 PM
  5. Need some info for waterbox mod
    By Chezzy in forum 4-Tec Performance
    Replies: 3
    Last Post: 03-25-2006, 09:13 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •