Results 1 to 8 of 8
  1. #1
    RXPRacer513's Avatar
    Join Date
    Jan 2009
    Location
    Huntersville, NC
    Posts
    234

    Wide Band Air Fuel Wiring

    Where is everybody been grounding the guage?
    As well as where is the power supply coming from?

    Good location would be much appreciated.
    Thanks


  2. #2
    dhoad's Avatar
    Join Date
    Aug 2005
    Location
    North Aurora, Illinois, United States
    Posts
    3,182
    +1
    6
    ground off the front of the block where the there is three ground bolts, follow the batt cable to find it
    power comes off the switched purple wire from mpem

  3. #3
    RXPRacer513's Avatar
    Join Date
    Jan 2009
    Location
    Huntersville, NC
    Posts
    234
    Thanks on the ground,
    Where in the purple wire do you attach, loction in ski?
    Thanks

  4. #4
    dhoad's Avatar
    Join Date
    Aug 2005
    Location
    North Aurora, Illinois, United States
    Posts
    3,182
    +1
    6

    .

    up front, take out storage bucket, to the left of hood shock, purple wire coming out of the grey connector at the very front of ski

  5. #5
    RXPRacer513's Avatar
    Join Date
    Jan 2009
    Location
    Huntersville, NC
    Posts
    234
    Thanks

  6. #6
    You should go direct to the battery with the Af meter. The O2 sensor draws quite a bit of current, especially on initial warm up. This is per the tech at Innovate.

    Mark

  7. #7
    R88ory RXP's Avatar
    Join Date
    Feb 2008
    Location
    Kent, England
    Posts
    2,737
    +1
    46
    Quote Originally Posted by Mark S View Post
    You should go direct to the battery with the Af meter. The O2 sensor draws quite a bit of current, especially on initial warm up. This is per the tech at Innovate.

    Mark
    +1 I have mine direct to the battery with a fuse and a switch. I put the dess key on switch LC1 on then start the ski. Takes a few seconds then you start to get readings. All good fun. R88

  8. #8
    RXPRacer513's Avatar
    Join Date
    Jan 2009
    Location
    Huntersville, NC
    Posts
    234
    Thanks for all the info!!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. FS CMD Marine, LCD-200, Wide Band 2 & Rude Fuel Controller
    By Tiburon1264 in forum Sea Doo Classifieds
    Replies: 5
    Last Post: 09-07-2014, 09:31 AM
  2. air/fuel gauge installed
    By shhr in forum 4-Tec Performance
    Replies: 30
    Last Post: 03-10-2007, 05:01 PM
  3. wiring the air/fuel gauge
    By shhr in forum Sea Doo Open Discussion
    Replies: 2
    Last Post: 06-01-2006, 09:57 PM
  4. air/fuel gauge ?
    By shhr in forum 4-Tec Performance
    Replies: 7
    Last Post: 04-17-2006, 10:59 PM
  5. Air/Fuel Gauge setup
    By Kinchyle in forum 4-Tec Performance
    Replies: 23
    Last Post: 04-12-2006, 08:54 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •