03-27-2009, 09:04 AM #1
skat trak 13/19 or 14/20 solas dynafly?
deciding between the 2 since my ski has the following mods recently put on
07gp1300- r&d rideplate(is. racing mod 1 resurface)
riva 1200 top loader intake
riva pump stuffer
riva ff exhaust
leos holeshot(stern holes blocked)
pump tunnel reinforcement (self made )
N0 ENGINE MODS OR FUEL TUNERS
i,m looking for more holeshot speed and midrange accelation for this'BAD BOY' top end is not a top priority ,like to hear from you guys on the forum
03-27-2009, 09:06 AM #2
skat trak 13/19 is a great prop
03-27-2009, 09:13 AM #3
- Join Date
- Jul 2005
- Central North Carolina
Dyna-Fly is the only prop to use for best all round performance!! 14/20
03-27-2009, 09:32 AM #4
13/19 vs 14/20
but i understand that it would be harder to turn the engine and to get my rpms up with the higher pitch , theres not a chance of me porting the engine or cat .removal etc.,as we all know this ski in PURE STOCK phase is a 'dog' in the hole it takes 20mph to get up on plane would,nt the dynafly still give' drag' early?
03-27-2009, 10:03 AM #5
I would say skat trak 13/19 swirl R. the prop doesn't lose top end and is good for a ski like that. But if your going to an aftermarket prop you should reinforce the tunnel and seal your pump shoe.
03-27-2009, 10:13 AM #6
i have a 1200r with similar mods the difference between the two is simple.
13/19 will give you very good bottom end and good mid good top end....
14/20 will give you slightly worse setoff, brilliant midrange and 3/4 throttle and better top...
i have both props and have swaped them both over the last week as i have done other mods now....
03-27-2009, 11:09 AM #7
YES! I AGREE ,SKAT TRAK 13/19 155 R SWIRL.its just that the shop thats installing it for me (could probably install myself but don't have the tool and being a little 'tricky' first time) says that RIVA SAID THAT 'THERE PUTTING THE SOLAS 14/20 DYNAFLY IN ALL THERE BOATS'. i disagree with that NEED MORE BOTTOM END!
(XSOCKGUYX)hi! jersey boy i think i mentioned that the tunnel reinforcement and pump seal have been installed THANKS!
03-27-2009, 11:43 AM #8
03-27-2009, 12:23 PM #9
Jet mediX ,toms river n.j.
03-27-2009, 12:27 PM #10
I would rather have my 5 year old cousing put it in for me instead of there...............Props are easy to install. If you have done the other stuff Prop should be no problem. When you order your prop you order the drive shaft tool. Hold it with a vice and then take the prop tool that comes with kit and put it on. PM me if you need a hand.
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
By meeper in forum 4-Tec PerformanceReplies: 6Last Post: 10-11-2013, 06:49 AM
By peachypete82 in forum Sea Doo ClassifiedsReplies: 4Last Post: 08-14-2008, 08:01 PM
By troyg1130 in forum Sea Doo ClassifiedsReplies: 0Last Post: 07-12-2008, 01:01 AM
By RXP_Noah in forum 4-Tec PerformanceReplies: 14Last Post: 03-01-2008, 01:02 AM
By Chezzy in forum 4-Tec PerformanceReplies: 22Last Post: 01-21-2007, 06:47 PM