Results 1 to 2 of 2
  1. #1
    Boilerman Bill BPnta's Avatar
    Join Date
    Jun 2008
    Location
    Yulee, FL
    Posts
    887
    +1
    1

    Need SHO impeller advice:

    I want to make sure I'm getting the right impeller for my SHO:

    I'm gonna do the following mods all at once:
    Power plenum air filter
    Intake manifold upgrade
    BOV w/ multi port adaptor

    Is the 12/22 impeller the right choice? Also- is the shaft holder the only tool I need to change impellers?


  2. #2
    mjh3ides's Avatar
    Join Date
    Jul 2007
    Location
    Jupiter, Florida
    Posts
    6,805
    +1
    2,024
    Quote Originally Posted by bpnta View Post
    I want to make sure I'm getting the right impeller for my SHO:

    I'm gonna do the following mods all at once:
    Power plenum air filter
    Intake manifold upgrade
    BOV w/ multi port adaptor

    Is the 12/22 impeller the right choice? Also- is the shaft holder the only tool I need to change impellers?
    See post #54 in this thread:
    http://greenhulk.net/forums/showthre...t=81103&page=6

    I had a few more mods(IC spacer & cooling kit) than you're planning when I tested this, but I think 13/22 is the ticket. Not sure if R&D has a part # for 13/22, but they buy stock Skat props & repitch them in-house, so they should be able to do it if it's not listed. Come cooler winter weather, your revs might be over 7550 with this pitch, which will make the boost limiter kick in but you'll probably be ready for more mods by then. You should be well off the rev limit though.

    You will need the shaft tool, prop tool(should come with the prop) & a bench vice. You will need a 27mm closed end wrench(preferably 6 point) & breaker bar to remove the stock prop. If you use a crescent wrench or open end wrench you will most likely damage the stock prop with the amount of torque required to remove it. The prop tool with the Skat will require a 1" closed end wrench. Again, if you use an open end wrench with the prop tool you will most likely warp it. You'll also need a small allen wrench(don't remember the size) to tighten the set screw on the Skat prop cone.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Need Impeller advice for 14' FZS
    By Seelow in forum Yamaha PWC Performance (4-stroke)
    Replies: 4
    Last Post: 08-19-2016, 04:58 AM
  2. SHO Impeller Advice
    By BlueWaterFZ in forum Yamaha PWC Performance (4-stroke)
    Replies: 11
    Last Post: 07-21-2016, 01:06 PM
  3. Got a new impeller, needs tweaking. Pitching advice, please!
    By Guy on the water in forum 4-Tec Performance
    Replies: 7
    Last Post: 06-29-2010, 08:36 AM
  4. Need a stock '08 SHO impeller
    By DCoog in forum Yamaha PWC Performance (4-stroke)
    Replies: 3
    Last Post: 06-23-2009, 06:03 PM
  5. Need an impeller
    By NCHeel in forum Sea Doo Open Discussion
    Replies: 11
    Last Post: 04-02-2006, 10:33 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •