Page 1 of 4 1 2 3 ... LastLast
Results 1 to 10 of 38
  1. #1
    1400gprmike's Avatar
    Join Date
    Jan 2009
    Location
    mia305
    Posts
    235

    Mike's GPRXP, yes, yet another 1 !!!

    Hello everyone want to start by saying thanks to everyone for all the help and info, without GH and its members this couldnt of happen so thanks again everyone. Well I kind of wanted to start the thread when I get my brackets and shalf which is in the mail and should arive this friday (thanks Mike), but with everything I've done so far I figure I'll start a thread and post everything I've done so far. Well I started with my original 2001 hull that once was a 1400, and I have a 2005 rxp setup to go in it. Im going with a closed loop system with a heat x that has 30 plates. Here's a couple of pics with whats already done.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	DSC04844.JPG 
Views:	121 
Size:	1.28 MB 
ID:	130159   Click image for larger version. 

Name:	DSC04848.JPG 
Views:	125 
Size:	1.06 MB 
ID:	130160  


  2. #2
    1400gprmike's Avatar
    Join Date
    Jan 2009
    Location
    mia305
    Posts
    235
    Here are my helpers/delyers!!!
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	DSC04857.JPG 
Views:	103 
Size:	1.17 MB 
ID:	130161   Click image for larger version. 

Name:	DSC04858.JPG 
Views:	97 
Size:	1.03 MB 
ID:	130162  

  3. #3
    1400gprmike's Avatar
    Join Date
    Jan 2009
    Location
    mia305
    Posts
    235
    Here's a couple pics of the innercooler mounted
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	DSC04849.JPG 
Views:	91 
Size:	1.08 MB 
ID:	130164   Click image for larger version. 

Name:	DSC04850.JPG 
Views:	90 
Size:	1.27 MB 
ID:	130165   Click image for larger version. 

Name:	DSC04851.JPG 
Views:	82 
Size:	1.17 MB 
ID:	130166  

  4. #4
    1400gprmike's Avatar
    Join Date
    Jan 2009
    Location
    mia305
    Posts
    235
    here's a couple of pics of a bracket i made to hold the heat x and coolant tank
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	DSC04852.JPG 
Views:	100 
Size:	1.17 MB 
ID:	130170   Click image for larger version. 

Name:	DSC04853.JPG 
Views:	110 
Size:	1.06 MB 
ID:	130171   Click image for larger version. 

Name:	DSC04854.JPG 
Views:	136 
Size:	1.07 MB 
ID:	130172   Click image for larger version. 

Name:	DSC04855.JPG 
Views:	90 
Size:	1.21 MB 
ID:	130173   Click image for larger version. 

Name:	DSC04856.JPG 
Views:	129 
Size:	988.6 KB 
ID:	130174  

  5. #5
    1400gprmike's Avatar
    Join Date
    Jan 2009
    Location
    mia305
    Posts
    235
    Some more pics, oh by the way please let me know if you guys see anything that wont work or if theres something i can do better, Tomorrow I plan of laying down and mounting the wire harness.

  6. #6
    "Hustler" Inkaddict's Avatar
    Join Date
    Aug 2007
    Location
    NJ
    Posts
    4,712
    +1
    26
    Out of curriosity... How come you cut the inner liner out on the side? Sure does make a whole lot of extra room...

  7. #7
    mrbtd's Avatar
    Join Date
    Jul 2005
    Location
    Lindenhurst, Illinois, United States
    Posts
    4,309
    +1
    2
    Where are you going to draw air for the S/C ? I dont have any of that in the rear and I could only run a 90 degree bend straight up and angled a little to avoid the J-Pipe.

    With the external IC and the driveline it is tough to run the air upfront unless you go over the top of the motor.

    Maybe the coolant bottle would be better inbetween the motor and the gas tank ?

  8. #8
    ecpChris's Avatar
    Join Date
    Jul 2007
    Location
    ocean county nj
    Posts
    2,912
    +1
    427
    Cute kids, I wish my son was willing to help with my build...
    You are going to need to change your screen name to 1500gprmike now

  9. #9
    Hydrotoys's Avatar
    Join Date
    Jul 2005
    Location
    Mesa, AZ
    Posts
    16,712
    +1
    85


    Consider changing out the rideplate inserts before going much further.

  10. #10
    1400gprmike's Avatar
    Join Date
    Jan 2009
    Location
    mia305
    Posts
    235
    Quote Originally Posted by Inkaddict View Post
    Out of curriosity... How come you cut the inner liner out on the side? Sure does make a whole lot of extra room...
    Quote Originally Posted by mrbtd View Post
    Where are you going to draw air for the S/C ? I dont have any of that in the rear and I could only run a 90 degree bend straight up and angled a little to avoid the J-Pipe.

    With the external IC and the driveline it is tough to run the air upfront unless you go over the top of the motor.

    Maybe the coolant bottle would be better inbetween the motor and the gas tank ?
    Quote Originally Posted by gprjersey07 View Post
    Cute kids, I wish my son was willing to help with my build...
    You are going to need to change your screen name to 1500gprmike now
    Quote Originally Posted by Hydrotoys View Post


    Consider changing out the rideplate inserts before going much further.

    Thanks guys for all the info and pointers, I bought the ski how it is, its cut all the way around and emptyed out for weight reduction. since the inside hull is cut like that, that is where I'll be running the riva intake for the sc, but wont know for sure untill the motor is in.
    Thanks, my kids for some reason really love riding for as little as they are, and everyday they ask me if the ski is done, to go ride.
    As for the inserts they are going to get changed out today along with installing the wire harness. Thanks again guys keep the info coming it really helps!!!

Page 1 of 4 1 2 3 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Yet another GPRXP build
    By toxicgun in forum Conversion PWC Performance Skis
    Replies: 136
    Last Post: 09-06-2017, 02:26 PM
  2. Yet another SC failure/warranty issue
    By 01xdime in forum 4-Tec Performance
    Replies: 32
    Last Post: 01-07-2007, 12:40 PM
  3. Yet another ride plate help thread (riva)
    By FSTGPR in forum Yamaha PWC Performance (2-stroke)
    Replies: 14
    Last Post: 07-06-2006, 05:43 PM
  4. Yet another EFI question...
    By Super in forum Yamaha PWC Performance (2-stroke)
    Replies: 17
    Last Post: 06-06-2006, 11:19 AM
  5. YET another question
    By shooter98xpl in forum Yamaha PWC Performance (2-stroke)
    Replies: 3
    Last Post: 12-19-2005, 07:32 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •