Results 1 to 3 of 3
  1. #1
    100 MILES OF HEAVEN AND I AM SMACK IN THE MIDDLE KEYZBUM's Avatar
    Join Date
    Apr 2007
    Location
    JUST NORTH OF CUBA-- FL,KEYS
    Posts
    2,556
    +1
    39

    03 1300R display -how to test??

    what wire/s do i need to put power to -so i can check if this gp1300r display is any good??
    looking at the ski - i bet less than 40 hours
    ski is stripped -no wiring left-so i need to cheet to test it
    oh and how do i get the side cowlings off WIYOUT BREAKING the tabs
    thanks
    matt


  2. #2
    Kid In A Adult Body sandman7793's Avatar
    Join Date
    May 2009
    Location
    Naples, FL
    Posts
    63
    Dont know if it is the same but on my 2000 i just removed the left hand side fairing and then the two 10 mm nuts on the inside of the hull under the front hood on each side then i just used a long extension and a 8mm socket and reached the clamps on the back of the gauge and then just unhooked the wire connectors and pulled it out. In the manual there is multiple tests you have to do so you probably need the book but on the 2000 gp 1200r you just put jumpers from the red wire in the six pin connector to + and the black wire from the same connector to - and then a jumper wire from the green back to the red but you should research this to be postive this is correct for your craft because it could be a six hundred dollar mistake

  3. #3
    100 MILES OF HEAVEN AND I AM SMACK IN THE MIDDLE KEYZBUM's Avatar
    Join Date
    Apr 2007
    Location
    JUST NORTH OF CUBA-- FL,KEYS
    Posts
    2,556
    +1
    39
    Quote Originally Posted by sandman7793 View Post
    Dont know if it is the same but on my 2000 i just removed the left hand side fairing and then the two 10 mm nuts on the inside of the hull under the front hood on each side then i just used a long extension and a 8mm socket and reached the clamps on the back of the gauge and then just unhooked the wire connectors and pulled it out. In the manual there is multiple tests you have to do so you probably need the book but on the 2000 gp 1200r you just put jumpers from the red wire in the six pin connector to + and the black wire from the same connector to - and then a jumper wire from the green back to the red but you should research this to be postive this is correct for your craft because it could be a six hundred dollar mistake
    thanks bro - i got it wired up and sold already --i was wrong about the hours -it had 54.6 ,,close to 40
    now if i can get somebody to test this 03 1300r ecu (from up in the bow)
    i dont evan want to waste time shipping it to somebody that needs it ,if i cant test it
    mattman

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. How to test thermostat
    By miamirider in forum 4-Tec Performance
    Replies: 17
    Last Post: 06-23-2008, 09:48 AM
  2. How to test Fuel Injectors
    By Mr Bill in forum Yamaha How To & FAQs
    Replies: 6
    Last Post: 07-18-2007, 04:23 PM
  3. how to test buzzer 96 spx
    By 95 sl750 in forum 2-Stroke Performance
    Replies: 4
    Last Post: 06-01-2007, 08:35 PM
  4. how to test oil injection
    By dont kno crap in forum Polaris How To & FAQs
    Replies: 24
    Last Post: 05-14-2007, 10:29 PM
  5. How to test the OPAS Blocks for water??
    By Totallyblown in forum 4-Tec Performance
    Replies: 2
    Last Post: 02-03-2006, 12:08 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •