Results 1 to 7 of 7
  1. #1

    Join Date
    Sep 2007
    Location
    Spicewood, Texas
    Posts
    20

    Correct sealant for pump to transom plate?

    I think this question is so basic that it may not be covered specifically on the board, because I have searched until my brain is goo. (But I have learned a lot along the way)

    For my '02 GPR I have installed a prop from Carl and plan to re-install the pump tonight, can I use 4200 between the pump and the transom plate or do I have to find some Yamabond or equivalent?

    Do I need to re-grease the splines on the shaft?

    Thanks guys! The information shared on this board is truly amazing and greatly appreciated by folks like me who can barely turn a wrench.


  2. #2
    mjh3ides's Avatar
    Join Date
    Jul 2007
    Location
    Jupiter, Florida
    Posts
    6,805
    +1
    2,024
    I think the svc manual recommends 1194, but I can never find it locally so I use Threebond 1211. I put a little grease on my shaft splines.

  3. #3

    Join Date
    Sep 2007
    Location
    Spicewood, Texas
    Posts
    20
    Threebond 1211 it is then!

    Thank you very much!

  4. #4
    Happily Self-Employed WFO's Avatar
    Join Date
    Nov 2005
    Location
    Houston, Texas
    Posts
    12,801
    +1
    450
    4200 will work, or 5200, or Yamabond, or Hondabond

  5. #5
    Quote Originally Posted by WFO View Post
    4200 will work, or 5200, or Yamabond, or Hondabond
    +1
    Just need something to keep it from suckin air.

  6. #6

    Join Date
    May 2008
    Location
    Lafayette, Indiana
    Posts
    27
    I just got done changing my prop and I used Yamabond. I would think twice before using either 4200 or especially 5200 as you are going to have to pull it apart again eventually for mods or maintenance.

  7. #7
    mrbtd's Avatar
    Join Date
    Jul 2005
    Location
    Lindenhurst, Illinois, United States
    Posts
    4,309
    +1
    2
    Nice part about yamabond or hondabond is permatex gasket remover makes clean up a breeze

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Correct bearings for pump rebuild!?!
    By Jamescmei in forum Yamaha PWC Performance (2-stroke)
    Replies: 5
    Last Post: 07-05-2016, 09:28 AM
  2. FS - Parts Stock transom plate, and pump shoe for 2000 XL
    By pokplalya22 in forum Yamaha Classifieds
    Replies: 0
    Last Post: 05-14-2013, 11:12 AM
  3. Question about bolt size from pump to transom plate
    By o uncola o in forum Yamaha PWC Performance (2-stroke)
    Replies: 13
    Last Post: 06-30-2009, 11:15 PM
  4. What ratio premix? Is it ok to leave to pump for a block off plate?
    By gvnitup in forum Polaris Open Discussion
    Replies: 8
    Last Post: 05-18-2007, 03:14 PM
  5. What sealer for Transom plate to pump?
    By LT1GMC in forum Yamaha PWC Performance (2-stroke)
    Replies: 1
    Last Post: 03-18-2007, 01:58 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •