Displaying Engine Temp On Dash

[Deanoo]

Wondering how can i display the engine temperature onto my dash

Ski is a 22 RXP-X

[r1goombah]

couple people offer a add on kit for $200, or you can build your own for under $100, not very hard to do,

[Turbo831]

I haven't seen anything for the new color dash's that will let you yet, dashpac would do it on the older dash versions. Dashpac may be working on something for them you could try contacting them to see if they're working on it yet. [email protected]

[r1goombah]

I've seen it done personally and friends 22 tx with color display. I'm sure he will chime in soon on this. I personally used the 3 way t off the pump from a gtx cause it comes with the temp sensor. And then the 2 wires run to the pcm. Hardest part about job is getting the correct pins to the ecu

[Yann]

I've seen it done personally and friends 22 tx with color display. I'm sure he will chime in soon on this. I personally used the 3 way t off the pump from a gtx cause it comes with the temp sensor. And then the 2 wires run to the pcm. Hardest part about job is getting the correct pins to the ecu

He want the engine temperature not the lake/sea temperature.
On the 2009 to 2018 semi digital cluster the engine temperature is display on the dash since 2019 she disappeared
On Can Am Maverick X3 turbo 2019 to 2022 the engine temperature is display on the dash, is the same dash than Seadoo models but not the same cluser software.

[TAB686]

Must use a factory Bosch sensor. And pin it in the b e2 and b g2. R1 can provide the link of the factory y with sensor. That's the easiest way. The pins are a molex. I'll have to look up the number.

[PPDJ]

You can buy this off eBay. If you split the hose coming off the front of the water pump you could also use with the closed loop cooling system to get engine temperature.

https://www.ebay.com/itm/33436791095...is&media=EMAIL

[TAB686]

That's what the OEM uses. For all temp sensors in the engine/exhaust and lake water temps

[TAB686]

Oh my bad. But you can use the same pins on the ecu and just put the sensor in the coolant. Or a dash pack like I have also

He want the engine temperature not the lake/sea temperature.
On the 2009 to 2018 semi digital cluster the engine temperature is display on the dash since 2019 she disappeared
On Can Am Maverick X3 turbo 2019 to 2022 the engine temperature is display on the dash, is the same dash than Seadoo models but not the same cluser software.

[Yann]

Oh my bad. But you can use the same pins on the ecu and just put the sensor in the coolant. Or a dash pack like I have also

The ECT sensor already exist, in this case you have to double the wire and plug the 2 news wires to ECM water tempererature entry

[TAB686]

The ECT sensor already exist, in this case you have to double the wire and plug the 2 news wires to ECM water tempererature entry

I knew the engine coolant temp sensor is already installed but feeding it into the ECU at a separate location I didn't think it would read correctly

[TAB686]

How about a pre charger air temp sensor?

[TAB686]

Now hull temps can be read. Y not right.

[DR2006RXP]

You can buy this off eBay. If you split the hose coming off the front of the water pump you could also use with the closed loop cooling system to get engine temperature.

https://www.ebay.com/itm/33436791095...is&media=EMAIL

Yes , plug and play.

[TAB686]

Yes that's what I said. And the cost is significantly lower when you build it. Either way you have to pin the ECU.

Yes , plug and play.