high idle with ribbon delete on VXR

[rosey]

2012 VXR has a high idle. I bypassed the exhaust resonator and put in an R&D ribbon delete. Now it is idleing really high. I can live with this but would like to get the idle back down to normal. What am I missing?
Any suggestions?
I have searched and cannot find a solution to my problem. Sorry if it has already been answered on another post.

Cheers

[Rt-HemiBoY]

Probably a vacuum leak check the gasket if you put it in.

[rosey]

THanks, I talked to the R&D guy. He said there should not be a change in idle with the ribbon delete. Maybe I pulled a hose loose or something but I am typically pretty careful about all of that. I will check it tonight. Thanks for the heads up.
Sure makes it hard and scary to trailer when Idle is at 3mph. lol.

[The Rooster]

Probably a vacuum leak check the gasket if you put it in.

+1. Make sure the small square black gasket did not fall down in the bottom of the ski. If I'm not mistaken it goes between the throttle body & intake. Removing the ribbon does not usually cause ideling issues.

[rosey]

According to the Service manual there is not a gasket at the throttle body. I do not recall seeing one either. The Joint (6) has a rubber coating on it that appeared to work as a gasket.

I forgot to add that I did drill out more ports in the back of the air filter case to allow more air and re-routed the ventilation hoses so they vent directly under the air filter case. Maybe all this fresh air changed the idle. I will be definately be tinkering with it tonight but welcome any ideas.

[The Rooster]

Rosey, not sure why there would be a difference but on the microfishe drawing for my N/A HO 1.8 it shows the gasket I was referring to behind #1 -Throttle body & # 11 - spacer. That's the one that is fairly easy to lose track of. Good luck !!!

[bryantjopplin]

THanks, I talked to the R&D guy. He said there should not be a change in idle with the ribbon delete. Maybe I pulled a hose loose or something but I am typically pretty careful about all of that. I will check it tonight. Thanks for the heads up.
Sure makes it hard and scary to trailer when Idle is at 3mph. lol.

What is your rpms? My will be at 3 mph with no throttle applied. Does the throttle response seems worse then new? If not I doubt you have a vacuum leak.

Rosey, not sure why there would be a difference but on the microfishe drawing for my N/A HO 1.8 it shows the gasket I was referring to behind #1 -Throttle body & # 11 - spacer. That's the one that is fairly easy to lose track of. Good luck !!!

The number 6 is the gasket basically. At least on mine it was attached to another piece, unless you mean something else.

[rosey]

Well now I am stumped! I removed throttle body cleaned all surfaces and put back together. It appears to be idling normally now. I am thinking some of the thread lock that had dripped on the rubber gasket surface may have caused a vacuum leak. Thanks for the help y'all.

On the factory gauge it is at 1k RPM now and sounds normal. This past weekend i did not pay attention but from the sound tonight, I think it was closer to 1.5 to 2k RPM when out on the Bay.
I will get it on the water this weekend and make sure.
Cheers
Clark

[bryantjopplin]

Well now I am stumped! I removed throttle body cleaned all surfaces and put back together. It appears to be idling normally now. I am thinking some of the thread lock that had dripped on the rubber gasket surface may have caused a vacuum leak. Thanks for the help y'all.

On the factory gauge it is at 1k RPM now and sounds normal. This past weekend i did not pay attention but from the sound tonight, I think it was closer to 1.5 to 2k RPM when out on the Bay.
I will get it on the water this weekend and make sure.
Cheers
Clark

Stock idle on these are 1300 +/- 100 RPM's. Says so right on the motor

[JoeyDFZS]

Probably had a manifold leak

[mckma]

Reset ecu you may have moved the butterfly in the throttle body

[uaeboy123]

same problem happen to my VXR 2011 it was from Body Spacer it was leaking from the rubber
check the attached pic...