2023 FX Predrilled Holes For Recdeck

[Mudcon]

Has anyone got one of the 2023 FX series that had the predrilled holes for the recdeck already there? My buddy and I both picked up 2023 FX Cruiser HO's and neither one of them was predrilled like was said to be. Just wondering if anyone else had theirs predrilled from yamaha.

[TXDroneRacer]

I picked up two 23 FX Limited SVHOs...

I edited this post.

I originally stated that "No predrilled holes." What I should have stated is that I did not see any predrilled holes from the top surface. See additional comments in reply #5.

I've watched the videos. It doesn't look like it will be difficult to align the RecDeck though.

[svhooo]

How does the messaging on this get so screwed up?

All the reviews of 2023 models have said pre-drilled holes... people start taking delivery, and no holes!? WTF

This is the same with the maps in the 22 FX Limited. All reviews said you'd get a map card included with your 22 FX Limited... I picked mine up, no card included.

[K447]

Reviewers are reviewing pre-release press fleet review models.
And relying upon info provided by the manufacturer reps at the press event.

Factory configurations and product pricing decisions are revised 

The customers get what the dealerÔÇÖs receive, sometime much later.

How does the messaging on this get so screwed up?

All the reviews of 2023 models have said pre-drilled holes... people start taking delivery, and no holes!? WTF

This is the same with the maps in the 22 FX Limited. All reviews said you'd get a map card included with your 22 FX Limited... I picked mine up, no card included.

[TXDroneRacer]

Regarding pre-drilled, I stuck my hand inside the hull, under the spaces where the one would drill holes to attach the RecDeck. I felt three small holes on each side. I am not sure if they are through holes. The diameter seems a bit small too, but I can't say for sure. I would have to pull up the factory SeaDek material to see if the holes go all the way through.

I guess there is a chance that the holes I felt are starter holes for where the RecDeck bolts will be installed.

[HotBurritoBody]

Can confirm, what you felt were the pre drilled holes. I think they drilled the holes, then covered them with the hydro mat. I just stuck a nail to pierce through the hydro mat so I knew where the holes were. Little bit of reverse drill action to the hydro mat and I was good to go!

[Mr. GP1800]

Can confirm, what you felt were the pre drilled holes. I think they drilled the holes, then covered them with the hydro mat. I just stuck a nail to pierce through the hydro mat so I knew where the holes were. Little bit of reverse drill action to the hydro mat and I was good to go!

Hey that’s good to hear.

Does this count as drilling a hole in your hull for all of the people who are scared shitless to do so?

[TXDroneRacer]

Does this count as drilling a hole in your hull for all of the people who are scared shitless to do so?

That made me laugh.

[TXDroneRacer]

Can confirm, what you felt were the pre drilled holes. I think they drilled the holes, then covered them with the hydro mat. I just stuck a nail to pierce through the hydro mat so I knew where the holes were. Little bit of reverse drill action to the hydro mat and I was good to go!

Great idea... Nail <-- What a great idea. I was trying to think of a way to check that. I thought a small drill bit and drill from the bottom up... but your idea is much better.

[K447]

... Nail <-- What a great idea. I was trying to think of a way to check that 

Seamstress pins or sewing needle.

Poke around until you find each factory hole. The pinpricks you make while hunting for the holes will not be visible afterwards.